View 298596-004_3019138.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

intel ? celeron ? processor for the pga370 socket up to 1.40 ghz on 0.13 micron process datasheet product features the intel ? celeron ? processor is designed for uni-processor based value pc desktops and is binary compatible with previous generation intel architecture processors. the intel celeron processor provides good performance for applications running on advanced operating systems such as windows* 95/98, windowsnt*, windows* 2000, windowsxp* and unix*. this is achieved by integrating the best attributes of intel processors?the dynamic execution performance of the p6 microarchitecture plus the capabilities of mmx? technology?bringing a balanced level of performance to the value pc market segment. the intel celeron processor offers the dependability you would expect from intel at an exceptional value. systems based on intel celeron processors also include the latest features to simplify system management and lower the cost of ownership for small business and home environments. available at 1.4 ghz, 1.30 ghz, 1.20 ghz, 1.10a ghz, 1a ghz and 900 mhz with 100 mhz system bus 256 kb on-die level 2 (l2) cache with error correcting code (ecc)) dual independent bus (dib) architecture: separate dedicated external system bus and dedicated internal high-speed cache bus internet streaming simd extensions for enhanced video, sound and 3d performance binary compatible with applications running on previous members of the intel microprocessor line dynamic execution micro architecture power management capabilities ? system management mode ? multiple low-power states optimized for 32-bit applications running on advanced 32-bit operating systems flip chip pin grid array (fc-pga2) packaging technology integrated high performance 16 kb instruction and 16 kb data, nonblocking, level one cache integrated full speed level two cache allows for low latency on read/store operations error-correcting code for system bus data may 2002 order number: 298596-004
datasheet information in this document is provided in connection with intel products. no license, express or implied, by estoppel or othe rwise, to any intellectual property rights is granted by this document. except as provided in intel's terms and conditions of sale for such products, inte l assumes no liability whatsoever, and intel disclaims any express or implied warranty, relating to sale and/or use of intel products including liabil ity or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property righ t. intel products are not intended for use in medical, life saving, or life sustaining applications. intel may make changes to specifications and product descriptions at any time, without notice. designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." int el reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. the intel ? celeron ? processor may contain design defects or errors known as errata which may cause the product to deviate from published specifications. current characterized errata are available on request. contact your local intel sales office or your distributor to obtain the latest specifications and before placing your product o rder. copies of documents which have an ordering number and are referenced in this document, or other intel literature may be obtaine d by calling 1-800- 548-4725 or by visiting intel's website at http://www.intel.com. copyright ? intel corporation, 2002 intel, celeron, mmx, pentium, and the intel logo are trademarks or registered trademarks of intel corporation or its subsidiari es in the united states and other countries. *other names and brands may be claimed as the property of others.
datasheet 3 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process contents 1.0 introduction................................................................................................................ ......... 9 1.1 terminology.........................................................................................................10 1.1.1 package and processor terminology ....................................................10 1.1.2 processor naming convention...............................................................11 1.2 related documents.............................................................................................12 2.0 electrical specifications................................................................................................... .13 2.1 processor system bus and v ref .......................................................................................... 13 2.2 clock control and low power states..................................................................14 2.2.1 normal state?state 1 ...........................................................................15 2.2.2 autohalt powerdown state?state 2...................................................15 2.2.3 stop-grant state?state 3 .....................................................................15 2.2.4 halt/grant snoop state?state 4 ........................................................15 2.2.5 sleep state?state 5..............................................................................16 2.2.6 deep sleep state?state 6 ....................................................................16 2.2.7 clock control..........................................................................................17 2.3 power and ground pins ......................................................................................17 2.3.1 phase lock loop (pll) power...............................................................17 2.4 decoupling guidelines ........................................................................................18 2.4.1 processor vcc core decoupling............................................................18 2.5 processor system bus clock and processor clocking .......................................19 2.6 voltage identification ...........................................................................................19 2.7 processor system bus unused pins...................................................................21 2.8 processor system bus signal groups ................................................................22 2.8.1 asynchronous vs. synchronous for system bus signals .......................23 2.8.2 system bus frequency select signals ..................................................24 2.9 test access port (tap) connection....................................................................25 2.10 maximum ratings................................................................................................25 2.11 processor voltage level specifications ..............................................................25 2.12 agtl system bus specifications........................................................................30 2.13 system bus timing specifications ......................................................................31 3.0 signal quality specifications ............................................................................................41 3.1 bclk/bclk# & picclk signal quality specifications and measurement guidelines ....................................................................................41 3.2 agtl signal quality specifications and measurement guidelines.....................42 3.2.1 overshoot/undershoot guidelines .........................................................43 3.2.2 overshoot/undershoot magnitude .........................................................44 3.2.3 overshoot/undershoot pulse duration...................................................44 3.2.4 activity factor .........................................................................................44 3.2.5 reading overshoot/undershoot specification tables............................45 3.2.6 determining if a system meets the overshoot/undershoot specifications .........................................................................................46 3.3 non-agtl signal quality specifications and measurement guidelines.............47 3.3.1 overshoot/undershoot guidelines .........................................................48 3.3.2 ringback specification ...........................................................................48 3.3.3 settling limit guideline...........................................................................49
intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 4 datasheet 3.4 vtt_pwrgd signal quality specification ......................................................... 49 3.4.1 transition region .................................................................................... 49 3.4.2 transition time........................................................................................ 50 3.4.3 noise ...................................................................................................... 50 4.0 thermal specifications and design considerations......................................................... 51 4.1 thermal specifications........................................................................................ 51 4.1.1 thermtrip# requirement................................................................... 51 4.1.2 thermal diode........................................................................................ 52 4.2 thermal metrology .............................................................................................. 52 5.0 mechanical specifications................................................................................................ 53 5.1 fc-pga2 mechanical specifications .................................................................. 53 5.2 recommended mechanical keep-out zones ..................................................... 55 5.3 processor markings ............................................................................................ 56 5.4 processor signal listing...................................................................................... 57 6.0 boxed processor specifications....................................................................................... 68 6.1 mechanical specifications................................................................................... 68 6.1.1 mechanical specifications for the fc-pga2 package ........................... 68 6.1.2 boxed processor heatsink weight......................................................... 70 6.2 thermal specifications........................................................................................ 70 6.2.1 boxed processor cooling requirements ............................................... 70 6.2.2 boxed processor thermal cooling solution clip ................................... 71 6.3 electrical requirements for the boxed processor............................................... 71 6.3.1 electrical requirements ......................................................................... 71 7.0 processor signal description ........................................................................................... 73 7.1 alphabetical signals reference .......................................................................... 73 7.2 signal summaries ............................................................................................... 80
datasheet 5 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process list of figures 1 integrated heat spreader (ihs) ............................................................................ 9 2 agtl bus topology in a uniprocessor configuration.........................................14 3 stop clock state machine ...................................................................................14 4 pll filter specification........................................................................................18 5 differential/single-ended clocking example.......................................................19 6v tt power good and bus select interconnect diagram .....................................21 7 bsel[1:0] example for a system design............................................................24 8 vcc static and transient tolerance ....................................................................28 9 clock waveform ..................................................................................................36 10 bclk/bclk#, picclk, and tck generic clock waveform ..............................37 11 system bus valid delay timings ........................................................................37 12 system bus setup and hold timings..................................................................38 13 system bus reset and configuration timings....................................................38 14 platform power-on sequence and timings ........................................................39 15 power-on reset and configuration timings.......................................................39 16 test timings (tap connection) ..........................................................................40 17 test reset timings .............................................................................................40 18 bclk/bclk#, picclk generic clock waveform at the processor pins ...........42 19 low to high agtl receiver ringback tolerance...............................................43 20 maximum acceptable agtl overshoot/undershoot waveform .........................47 21 non-agtl overshoot/undershoot, settling limit, and ringback ......................47 22 noise estimation .................................................................................................50 23 package dimensions...........................................................................................53 24 volumetric keep-out ...........................................................................................55 25 component keep-out .........................................................................................55 26 top side processor markings .............................................................................56 27 processor pinout ................................................................................................57 28 conceptual boxed processor for the pga370 socket ........................................68 29 comparison between fc-pga and fc-pga2 package......................................69 30 side view of space requirements for the boxed processor ..............................69 31 dimensions of mechanical step feature in heatsink base.................................70 32 thermal airspace requirement for all boxed processor fan heatsinks in the pga370 socket ........................................................................71 33 boxed processor fan heatsink power cable connector description.................72 34 motherboard power header placement relative to the boxed processor..........72
intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 6 datasheet list of tables 1 processor identification....................................................................................... 11 2 system bus clock in deep sleep mode (differential mode only) ....................... 16 3 voltage identification definition .......................................................................... 20 4 system bus signal groups ................................................................................ 23 5 frequency select truth table for bsel[1:0] ...................................................... 24 6 absolute maximum ratings ................................................................................ 25 7 voltage and current specifications..................................................................... 26 8 power supply current slew rate (dicccore/dt)................................................... 27 9 vcc static & transient tolerance........................................................................ 28 10 agtl signal group levels specifications .......................................................... 29 11 non-agtl signal group levels specifications .................................................. 29 12 3.3 volt cmos output signal group dc specifications ..................................... 30 13 processor agtl bus specifications ................................................................... 30 14 system bus timing specifications (single-ended clock) ................................... 31 15 system bus timing specifications (differential clock) ....................................... 32 16 valid system bus to core frequency ratios ..................................................... 33 17 system bus timing specifications (agtl signal group) ................................... 33 18 system bus timing specifications (cmos signal group) .................................. 33 19 system bus timing specifications (reset conditions) ...................................... 34 20 system bus timing specifications (apic clock and apic i/o) .......................... 34 21 system bus timing specifications (tap connection) ........................................ 35 22 platform power-on timings ................................................................................ 36 23 bclk (single-ended clock mode) signal quality specifications for simulation at the processor pins ........................................................................ 41 24 bclk/bclk# (differential clock mode) and picclk signal quality specifications for simulation at the processor pins............................................ 41 25 agtl signal groups ringback tolerance specifications at the processor pins .................................................................................................... 42 26 example platform information............................................................................. 45 27 100 mhz agtl signal group overshoot/undershoot tolerance ...................... 46 28 33 mhz cmos signal group overshoot/undershoot tolerance........................ 48 29 signal ringback specifications for non-agtl signal simulation at the processor pins .................................................................................................... 49 30 processor thermal design power ..................................................................... 51 31 thermtrip# time requirement....................................................................... 51 32 thermal diode parameters ................................................................................. 52 33 thermal diode interface...................................................................................... 52 34 the processor package dimensions .................................................................. 54 35 processor case loading parameters ................................................................. 54 36 signal listing in order by signal name .............................................................. 58 37 signal listing in order by pin number ................................................................ 63 38 boxed processor fan heatsink spatial dimensions........................................... 70 39 fan heatsink power and signal specifications................................................... 72 40 signal description ............................................................................................... 73 41 output signals..................................................................................................... 80 42 input signals ....................................................................................................... 80 43 input/output signals (single driver).................................................................... 81 44 input/output signals (multiple driver) ................................................................. 82
datasheet 7 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process revision history revision date description -004 may 2002 ? added 1.4 ghz processor information; added section 3.4, ?vtt_pwrgd signal quality specification?; updated table 40, ?signal description? for v cmos_ref .
intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 8 datasheet this page is intentionally left blank.
datasheet 9 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 1.0 introduction the intel ? celeron ? processor based on 0.13 micron process core for the pga370 socket is the next member of the p6 family, in the intel ia-32 processor line and hereafter will be referred to as simply ?the processor?. the processor will continue in the package technology called flip-chip pin grid array but will contain a integrated heat spreader (ihs) (see figure 1 ). the flip-chip with ihs package will be labeled as fc-pga2 and will utilize the same 370-pin zero insertion force socket (pga370). thermal solutions contact the ihs directly for the fc-pga2 package and not to the bare-die as with the fc-pga attachment. the processor, like its predecessors in the p6 family of processors, implements a dynamic execution microarchitecture?a unique combination of multiple branch prediction, data flow analysis, and speculative execution. the processor delivers higher performance than the intel ? celeron ? processor based on 0.18 micron process core, while maintaining binary compatibility with all previous intel architecture processors. the processor also executes intel ? mmx tm technology instructions for enhanced media and communication performance just as the predecessor celeron processor based on 0.18 micron process core. additionally, the processor executes streaming simd (single-instruction, multiple data) extensions for enhanced floating point and 3-d application performance. the processor utilizes multiple low-power states such as stop-grant, sleep, and deep sleep to conserve power during idle times. the processor includes an integrated on-die, 256kb 8-way set associative level-two (l2) cache. the l2 cache implements the advanced transfer cache architecture with a 256-bit wide bus. the processor also includes a 16 kb level one (l1) instruction cache and 16 kb l1 data cache. these cache arrays run at the full speed of the processor core. the processor for the pga370 socket has a dedicated l2 cache bus, thus maintaining the dual independent bus architecture to deliver high bus bandwidth and performance. memory is cacheable for 64 gb of addressable memory space, allowing significant headroom for desktop systems. refer to the specification update document for this processor to determine the cacheability and cache configuration options for a specific processor. contact your nearest intel sales representative for the latest processor specification update. the processor will support a lower voltage differential and single-ended clocking for the system bus. the previous generation intel celeron processors for the pga370 socket will function in a platform that supports this processor, if the platform has been designed to be backward compatible. in addition, the processor will not function in a previous generation platform due to incompatible system bus signal levels and clock type. care must be taken to ensure the correct processors are installed in the correct pga370 socket platforms. figure 1. integrated heat spreader (ihs) fc-pga2 w/ihs fc-pga
10 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 1.1 terminology in this document, a ?#? symbol after a signal name refers to an active low signal. this means that a signal is in the active state (based on the name of the signal) when driven to a low level. for example, when flush# is low, a flush has been requested. when nmi is high, a nonmaskable interrupt has occurred. in the case of signals where the name does not imply an active state but describes part of a binary sequence (such as address or data ), the ?#? symbol implies that the signal is inverted. for example, d[3:0] = ?hlhl? refers to a hex ?a?, and d[3:0]# = ?lhlh? also refers to a hex ?a? (h= high logic level, l= low logic level). the term ?system bus? refers to the interface between the processor, system core logic (a.k.a. the chipset components), and other bus agents. 1.1.1 package and processor terminology the following terms are used often in this document and are explained here for clarification: ? the processor - the entire product including all internal components. ? 256k up processor - the desktop version of the 0.13 micron process processor. contains 256kb of l2 cache and is uni-processor capable only. ? pga370 socket - 370-pin zero insertion force (zif) socket which a fc-pga packaged processor plugs into. ? fc-pga - flip chip pin grid array. the package technology used on processors based on the 0.18 micron process for the pga370 socket. the fc-pga package has the processor die exposed. ? fc-pga2 - flip chip pin grid array 2. the package technology used on the processor for the pga370 socket. the fc-pga2 package contains an integrated heat spreader which covers the processor die. ? advanced transfer cache (atc) - l2 cache architecture used on the celeron ? processors. atc consists of microarchitectural improvements that provide a higher data bandwidth interface into the processor core that is completely scaleable with the processor core frequency. ? keep-out zone - the area on or near a fc-pga packaged processor that system designs can not utilize. ? keep-in zone - the area of a fc-pga packaged processor that thermal solutions may utilize. ? processor - for this document, the term processor is the generic form of the celeron ? processor based on 0.13 micron process core for the pga370 socket in the fc-pga2 package. ? processor core - the processor?s execution engine. ? integrated heat spreader (ihs) - the integrated heat spreader (ihs) is a metal cover on the die and it is an integral part of the processor. the ihs promotes heat spreading away from the die backside to ease thermal constraints . the cache and l2 cache are industry designated names.
datasheet 11 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 1.1.2 processor naming convention notes: 1. refer to the intel ? celeron ? processor specification update for the exact cpuid for each processor. 2. atc = advanced transfer cache. atc is an l2 cache integrated on the same die as the processor core. with atc, the interface between the processor core and l2 cache is 256-bits wide, runs at the same frequency as the processor core and has enhanced buffering. 3. 1.20 ghz at vcc core = 1.475 volts and s-spec number sl5xs. table 1. processor identification processor core frequency system bus frequency (mhz) l2 cache size (kbytes) l2 cache type 2 cpuid 1 1.4 1.40 100 256 atc 06bxh 1.30 1.30 ghz 100 256 atc 06bxh 1.20 3 1.20 ghz 100 256 atc 06bxh 1.20 1.20 ghz 100 256 atc 06bxh 1.10a 1.10a ghz 100 256 atc 06bxh 1a 1a ghz 100 256 atc 06bxh 900 900 mhz 100 256 atc 06bxh
12 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 1.2 related documents the reader of this specification should also be familiar with material and concepts presented in the following documents 1,2 : notes: 1. unless otherwise noted, this reference material can be found on the intel developer?s website located at http://developer.intel.com. 2. for a complete listing of intel celeron processor reference material, please refer to the intel developer?s website at http://developer.intel.com/design/celeron/. 3. this material is available through an intel field sales representative. document intel order number ap-485, intel ? processor identification and the cpuid instruction 241618 ap-589, design for emi 243334 intel ? architecture software developer's manual 243193 volume i: basic architecture 243190 volume ii: instruction set reference 243191 volume iii: system programming guide 243192 p6 family of processors hardware developer?s manual 244001 ia-32 processors and related products 1999 databook 243565 370-pin socket (pga370) design guidelines 244410 pga370 heat sink cooling in microatx chassis 245025 815 b-step chipset platform design guide 3 ck-815 clock synthesizer/driver specification 3 ck-408 clock synthesizer/driver specification 3 vrm 8.5 dc-dc converter design guidelines 3 249659 extensions to the pentium ? pro processor bios writer?s guide revision 3 intel ? pentium ? iii processor in the fc-pga2, 370-pin package thermal design guidelines 3 249660
datasheet 13 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.0 electrical specifications 2.1 processor system bus and v ref the processor uses the original low voltage signaling of the gunning transceiver logic (gtl) technology for the system bus. the gtl system bus operates at 1.25v signal levels versus gtl+ which operates at 1.5 v signal levels. the gtl+ signal technology is used by the intel ? pentium ? pro, intel ? pentium ? ii and intel ? pentium ? iii processors. current p6 family processors vary from the intel ? pentium ? pro processor in their output buffer implementation. the buffers that drive the system bus signals on the processor are actively driven to v tt for one clock cycle after the low to high transition to improve rise times. these signals are open-drain and require termination to a supply. because this specification is different from the standard gtl specification, it is referred to as agtl, or assisted gtl in this and other documentation related to the processor. agtl logic and agtl+ logic are not compatible with each other due to differences with the signal switching levels. the processor cannot be installed into platforms where the chipset only supports the agtl+ signal levels. for more information on agtl or agtl+ routing, please refer to the appropriate platform design guide. agtl inputs use differential receivers which requires a reference voltage (v ref ). v ref is used by the differential receivers to determine if the input signal is a logical 0 or a logical 1. the v ref signal is typically implemented as a voltage divider on the platform. noise decoupling is critical for the v ref signal. refer to the platform design guide for the recommended decoupling requirements. another important item for the agtl system bus is termination. system bus termination is used to pull each signal to a high voltage level and to control reflections on the transmission line. the processor contains on-die termination resistors that provide termination for one end of the system bus. the other end of the system bus should also be terminated near the chipset by resistors placed on the platform or on-die termination within the chipset. it is recommended that the system bus is implemented using dual-end termination (det) to meet the timings and signal integrity specified by the processor. figure 2 is a schematic representation of the agtl bus topology for the processor, when the chipset has does not have on- die termination. note: the reset# signal requires a discrete external termination resistor on the system board. the agtl bus depends on incident wave switching. therefore, timing calculations for agtl signals are based on flight time as opposed to capacitive deratings. analog signal simulations of the system bus, including trace lengths, is highly recommended especially when not following the recommended layout guidelines.
14 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.2 clock control and low power states processors allow the use of sleep, and deep sleep states to reduce power consumption by stopping the clock to internal sections of the processor, depending on each particular state. see figure 3 for a visual representation of the processor low power states. for the processor to fully realize the low current consumption of the stop-grant, sleep and deep sleep states, a model specific register (msr) bit must be set. for the msr at 02ah (hex), bit 26 must be set to a ?1? (this is the power on default setting) for the processor to stop all internal clocks during these modes. for more information, see the intel architecture software developer?s manual, volume 3: system programming guide . figure 2. agtl bus topology in a uniprocessor configuration processor chipset i/o i/o note: reset# requires external termination. figure 3. stop clock state machine pcb757a 2. auto halt power down state bclk running. snoops and interrupts allowed. halt i ns t ruc ti on an d halt bus cycle generated init#, binit#, intr, smi#, reset# 1. normal state normal execution. stpclk# asserted stpclk# de-asserted 3. stop grant state bclk running. snoops and interrupts allowed. slp# asserted slp# de-asserted 5. sleep state bclk running. no snoops or interrupts allowed. bclk input stopped bclk input restarted 6. deep sleep state bclk stopped. no snoops or interrupts allowed. 4. halt/grant snoop state bclk running. service snoops to caches. snoop event occurs snoop event serviced snoop event occurs snoop event serviced stpclk# asserted stpclk# de-asserted and stop-grant state entered from autohalt
datasheet 15 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.2.1 normal state?state 1 this is the normal operating state for the processor. 2.2.2 autohalt powerdown state?state 2 autohalt is a power state entered when the processor executes the halt instruction. the processor transitions to the normal state upon the occurrence of smi#, init#, or lint[1:0] (nmi, intr). reset# causes the processor to immediately initialize itself. the return from a system management interrupt (smi) handler can be to either normal mode or the autohalt power down state. see the intel architecture software developer's manual, volume iii: system programmer's guide for more information. flush# is serviced during the autohalt state, and the processor will return to the autohalt state. the system can generate a stpclk# while the processor is in the autohalt power down state. when the system deasserts the stpclk# interrupt, the processor returns execution to the halt state. 2.2.3 stop-grant state?state 3 the stop-grant state on the processor is entered when the stpclk# signal is asserted. since the agtl signal pins receive power from the system bus, these pins should not be driven (allowing the level to return to v tt ) for minimum power drawn by the termination resistors in this state. in addition, all other input pins on the system bus should be driven to the inactive state. binit# and flush# are not serviced during the stop-grant state. reset# causes the processor to immediately initialize itself, but the processor stays in stop-grant state. a transition back to the normal state occurs with the deassertion of the stpclk# signal. a transition to the halt/grant snoop state occurs when the processor detects a snoop on the system bus (see section 2.2.4 ). a transition to the sleep state (see section 2.2.5 ) occurs with the assertion of the slp# signal. while in stop-grant state, smi#, init#, and lint[1:0] are latched by the processor, and only serviced when the processor returns to the normal state. only one occurrence of each event is recognized and serviced upon return to the normal state. 2.2.4 halt/grant snoop state?state 4 the processor responds to snoop transactions on the system bus while in stop-grant state or in autohalt power down state. during a snoop transaction, the processor enters the halt/grant snoop state. the processor stays in this state until the snoop on the system bus has been serviced (whether by the processor or another agent on the system bus). after the snoop is serviced, the processor returns to the stop-grant state or autohalt power down state, as appropriate.
16 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.2.5 sleep state?state 5 the sleep state is a very low power state in which the processor maintains its context, maintains the phase-locked loop (pll), and has stopped all internal clocks. the sleep state can only be entered from the stop-grant state. once in the stop-grant state, the slp# pin can be asserted, causing the processor to enter the sleep state. the slp# pin is not recognized in the normal or autohalt states. snoop events that occur while in sleep state or during a transition into or out of sleep state will cause unpredictable behavior. in the sleep state, the processor is incapable of responding to snoop transactions or latching interrupt signals. no transitions or assertions of signals (with the exception of slp# or reset#) are allowed on the system bus while the processor is in sleep state. any transition on an input signal before the processor has returned to stop-grant state will result in unpredictable behavior. if reset# is driven active while the processor is in the sleep state, and held active as specified in the reset# pin specification, then the processor will reset itself, ignoring the transition through stop-grant state. if reset# is driven active while the processor is in the sleep state, the slp# and stpclk# signals should be deasserted immediately after reset# is asserted to ensure the processor correctly executes the reset sequence. while in the sleep state, the processor is capable of entering its lowest power state, the deep sleep state, by stopping the bclk input (see section 2.2.6 ). once in the sleep state, the slp# pin can be deasserted if another asynchronous system bus event occurs. the slp# pin has a minimum assertion of one bclk period. 2.2.6 deep sleep state?state 6 the deep sleep state is the lowest power state the processor can enter while maintaining context. the deep sleep state is entered by stopping the bclk input (after the sleep state was entered from the assertion of the slp# pin). the processor is in deep sleep state immediately after bclk is stopped. bclk and bclk# have to be separated by at least 0.2v during the deep sleep state. stopping of the bclk input lowers the overall current consumption to leakage levels. to re-enter the sleep state, the bclk input must be restarted. a period of 1 ms (to allow for pll stabilization) must occur before the processor can be considered to be in the sleep state. once in the sleep state, the slp# pin can be deasserted to re-enter the stop-grant state. while in deep sleep state, the processor is incapable of responding to snoop transactions or latching interrupt signals. no transitions or assertions of signals are allowed on the system bus while the processor is in deep sleep state. any transition on an input signal before the processor has returned to stop-grant state will result in unpredictable behavior. notes: 1. the values in this table are based on differential probe measurement of the bclk. 2. the dc voltage level specified must be maintained when the system bus clock is not active (e.g., deep sleep mode). v bclk# has to be 200 mv less than v bclk . table 2. system bus clock in deep sleep mode (differential mode only) symbol parameter min max units notes 1 v bclk bclk voltage level when not active 0.4 1.45 v 2 v bclk ?v bclk# bclk# voltage level when not active 0 v bclk ? 0.2 v 2
datasheet 17 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.2.7 clock control bclk provides the clock signal for the processor and on-die l2 cache. during autohalt power down and stop-grant states, the processor will process a system bus snoop. the processor does not stop the clock to the l2 cache during autohalt power down or stop-grant states. entrance into the halt/grant snoop state allows the l2 cache to be snooped, similar to the normal state. when the processor is in sleep and deep sleep states, it does not respond to interrupts or snoop transactions. during the sleep state, the internal clock to the l2 cache is not stopped. during the deep sleep state, the internal clock to the l2 cache is stopped. the internal clock to the l2 cache is restarted only after the internal clocking mechanism for the processor is stable (i.e., the processor has re-entered sleep state). picclk should not be removed during the autohalt power down or stop-grant states. picclk can be removed during the sleep or deep sleep states. when transitioning from the deep sleep state to the sleep state, picclk must be restarted with bclk. 2.3 power and ground pins the operating voltage for the processor is the same for the core and the l2 cache. v cc core is defined as the power pins that supply voltage to the processor?s core and cache. the voltage regulator module (vrm) or voltage regulator are controlled by the five voltage identification (vid) signals driven by the processor. the vid signals specify the voltage required by the processor core. refer to section 2.6 for further details on the vid voltage settings. the processor has 74 v cc core , 7 v ref , 20 v tt , v cc cmos1.5 , v cc cmos1.8, v cc cmos2.0 and 74 v ss inputs. the v ref inputs are used as the agtl reference voltage for the processor. the v tt inputs (1.25v) are used to provide an agtl termination voltage to the processor. v cc cmos1.5 and v cc cmos1.8 and v cc cmos2.0 are not voltage input pins to the processor but rather voltage sources for the pullup resistors which are connected to cmos (non-agtl) input/output signals driven to/ from the processor. the v ss inputs are ground pins for the processor core and l2 cache. on the platform, all v cc core pins must be connected to a voltage island (an island is a portion of a power plane that has been divided, or an entire plane) to minimize any voltage drop that may occur due to trace impedance. it is also highly recommended for the platform to provide either a voltage island or a wide trace for the v tt pins. similarly, all vss pins must be connected to a system ground plane. these recommendations can be found in the platform design guide layout section. 2.3.1 phase lock loop (pll) power it is highly critical that phase lock loop power delivery to the processor meets intel?s requirements. a low pass filter is required for power delivery to pins pll1 and pll2. this serves as an isolated, decoupled power source for the internal pll. refer to the phase lock loop power section in the appropriate platform design guide for the recommended filter implementation.
18 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.4 decoupling guidelines due to the large number of transistors and high internal clock speeds, the processor is capable of generating large average current swings between low and full power states. the fluctuations can cause voltages on power planes to sag below their nominal values if bulk decoupling is not adequate. care must be taken in the board design to ensure that the voltage provided to the processor remains within the specifications listed in table 7 . failure to do so can result in timing violations (in the event of a voltage sag) or a reduced lifetime of the component (in the event of a voltage overshoot). 2.4.1 processor v cc core decoupling the regulator for the v cc core input must be capable of delivering the di cc core /dt (defined in table 7 ) while maintaining the required tolerances (also defined in table 7 ). failure to meet these specifications can result in timing violations (during v cc core sag) or a reduced lifetime of the component (during v cc core overshoot). the processor requires both high frequency and bulk decoupling on the system motherboard for proper agtl bus operation. the minimum recommendation for the processor decoupling requirement is listed below. all capacitors should be placed next to and within the pga370 socket cavity and mounted on the primary side of the motherboard. the capacitors are arranged to minimize the overall inductance between the v cc core and vss power pins. decoupling recommendations: ? v cc core decoupling: a minimum of sixteen 4.7 uf capacitors in a 1206 package. ? v tt decoupling: twenty 0.1 uf capacitors in 0603 packages. ? v ref decoupling: 0.1 uf and 0.001 uf capacitors in 0603 package placed near the v ref pins. for additional decoupling requirements, refer to the appropriate platform design guide for recommended capacitor component value/quantity and placement. figure 4. pll filter specification 0.2 db 0 db -0.5 db forbidden zone forbidden zone -40 db -28 db dc fpeak 1 mhz 66 mhz force
datasheet 19 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.5 processor system bus clock and processor clocking the processor will implement an auto-detect mechanism that will allow the processor to use either single-ended or differential signaling for the system bus and processor clocking. the processor checks to see if the signal on pin y33 is toggling. if this signal is toggling then the processor operates in differential mode. refer to figure 5 for an example on differential clocking. resistor values and clock topology are listed in the appropriate platform design guide for a differential implementation. note: references to bclk throughout this document will also imply to it?s complement signal, bclk# in differential implementations, and when noted otherwise. since legacy pga370 socket platforms use a different single-ended clocking specification than the processor, the processor will not function when placed into these platforms. the bclk input directly controls the operating speed of the system bus interface. all agtl system bus timing parameters are specified with respect to the crossing point of the rising edge of the bclk and the falling edge of bclk# inputs in a differential implementation. see the p6 family of processors hardware developer's manual for further details. the reference voltage of the bclk in the p6 family of processors hardware developer manual is re-defined as the crossing point of the bclk and bclk# in a differential implementation. 2.6 voltage identification there are five voltage identification (vid) pins on the pga370 socket. these pins can be used to support automatic selection of v cc core voltages. the vid pins for the processor are open drain signals versus opens or shorts found on the previous intel celeron fc-pga processor. refer to table 11 for level specifications for the vid signals. this pull-up resistor may be either external logic on the motherboard or internal to the voltage regulator. the vid signals rely on a 3.3 v pull-up resistor to set the signal to a logic high level. the vid pins are needed to fully support voltage specification variations on current and future processors. the voltage selection range for the processor is defined in table 3 . the vid25mv signal is a new signal that allows the voltage regulator or voltage regulator module (vrm) to output voltage levels in 25 mv increment necessary for the processor only. the current celeron processor in the fc- pga package will not have this vid25mv signal. the vid25mv pin location is actually a vss pin figure 5. differential/single-ended clocking example clk e diff si l bclk bclk# clock driver processor or chipset + ? clock driver processor or chipset bclk
20 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process on the model 68xh based on 0.18 micron process core processor. by connecting the vid25mv signal to the vss pin, it will disable the 25 mv stepping granularity output and the regulator will resort to 50 mv stepping increment. the voltage regulator or vrm must supply the voltage that is requested or disable itself. in addition to the new signal ?vid25mv?, the processor will introduce a second new signal labeled as ?vtt_pwrgd?. the vtt_pwrgd signal informs the platform that the vid and bsel signals are stable and should be sampled. during power-up, the vid signals will be in an indeterminate state for a small period of time. the voltage regulator or the vrm should not latch the vid signals until the vtt_pwrgd signal is asserted by the vrm and sampled active. the assertion of the vtt_pwrgd signal indicates the vid signals are stable and are driven to the final state by the processor. refer to figure 14 for power-up timing sequence for the vtt_pwrgd and the vid signals. notes: 1. 0 = processor pin connected to v ss . and 1 = open on processor; may be pulled up to ttl v ih (3.3 v max) on baseboard. table 3. voltage identification definition 1 vid25mv vid3 vid2 vid1 vid0 vcc core 00100 1.05 10100 1.075 00011 1.10 10011 1.125 00010 1.15 10010 1.175 00001 1.20 10001 1.225 00000 1.25 10000 1.275 01111 1.30 11111 1.325 01110 1.35 11110 1.375 01101 1.40 11101 1.425 01100 1.45 11100 1.475 01011 1.50 11011 1.525 01010 1.55 11010 1.575 01001 1.60 11001 1.625 01000 1.65 11000 1.675 00111 1.70 10111 1.725 00110 1.75 10110 1.775 00101 1.80 10101 1.825
datasheet 21 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process the vid pins should be pulled up to a 3.3 v level. this may be accomplished with pull-ups internal to the voltage regulator, which ensures valid vid pull-up voltage during power-up and power-down sequences. if external resistors are used for the vid[3:0, 25mv] signal, then the power source must be guaranteed to be stable whenever the supply to the voltage regulator is stable. this will prevent the possibility of the processor supply going above the specified v cc core in the event of a failure in the supply for the vid lines. in the case of a dc-to-dc converter, this can be accomplished by using the input voltage to the converter for the vid line pull-ups. a resistor equal to 1 k ? may be used to connect the vid signals to the voltage regulator input. note: intel requires that designs utilize vrm 8.5 and not vrm 8.4 guidelines to meet the processor requirements. to re-emphasize, vrm 8.5 introduces two new signals [vid25mv and vtt_pwrgd] that is utilized by the processor and platform. ignoring and not connecting these two new pins, as documented in the platform design guidelines, will prevent the processor from operating at the specified voltage levels and core frequency. figure 6 provides a high-level interconnection schematic. refer to the vrm 8.5 dc-dc converter design guideline and the appropriate platform design guidelines for further detailed information on the voltage identification and bus select implementation. refer to figure 14 for vid power-up sequence and timing requirements. 2.7 processor system bus unused pins all reserved pins must remain unconnected unless specifically noted. connection of these pins to v cc core , v ref , v ss , v tt or to any other signal (including each other) can result in component malfunction or incompatibility with future processors. see section 5.4 for a pin listing of the processor and the location of each reserved pin. picclk must be driven with a valid clock input and the picd[1:0] signals must be pulled-up to v cc cmos1.5 even when the apic will not be used. a separate pull-up resistor must be provided for each picd signal. for reliable operation, always connect unused inputs or bidirectional signals to their deasserted signal level. the pull-up or pull-down resistor values are system dependent and should be chosen such that the logic high (v ih ) and logic low (v il ) requirements are met. see table 11 for level specifications of non-agtl signals. figure 6. v tt power good and bus select interconnect diagram vrm 8.5 voltage regulator vtt_pwrgd (output) v tt intel ? celeron processor based on 0.13 micron process vtt_pwrgd (input) v tt v cc core v tt v cc core 1 k ? clock driver bsel[1:0] vid[3:0, 25mv]
22 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process for unused agtl inputs, the on-die termination will be sufficient. no external r tt is necessary on the motherboard for unused cmos inputs, active low signals should be connected through a pull-up resistor to v cc cmos1.5 and meet v ih requirements. unused active high cmos inputs should be connected through a pull-down resistor to ground (v ss ) and meet v il requirements. unused cmos outputs can be left unconnected. a resistor must be used when tying bidirectional signals to power or ground. when tying any signal to power or ground, a resistor will also allow for system testability. 2.8 processor system bus signal groups to simplify the following discussion, the processor system bus signals have been combined into groups by buffer type. all p6 family processor system bus outputs are open drain and require a high-level source provided termination resistors. however, the processor includes on-die termination for agtl signals and termination resistors placed on the platform are not necessary except for the reset# signal which still requires external termination. agtl input signals have differential input buffers which use v ref as a reference signal. agtl output signals require termination to 1.25 v. in this document, the term ?agtl input? refers to the agtl input group as well as the agtl i/o group when receiving. similarly, ?agtl output? refers to the agtl output group as well as the agtl i/o group when driving. the pwrgood signal input is a 1.8 v signal level and must be pulled up to v cc cmos1.8 . the vtt_pwrgd is not 1.8 v tolerant and must be connected to v tt ( 1.25 v) . other cmos inputs (a20m#, ignne#, init#, lint0/intr, lint1/nmi, preq#, smi, slp#, and stpclk#) are only 1.5 v tolerant and must be pulled up to v cc cmos1.5 . the cmos, apic, and tap outputs are open drain and must be pulled to the appropriate level to meet the input specifications of the interfacing device. the groups and the signals contained within each group are shown in table 4 . refer to section 7.0 for a description of these signals.
datasheet 23 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process notes: 1. see section 7.0 for information on the these signals. 2. the br0# pin is the only breq# signal that is bidirectional. see section 7.0 for more information. 3. this signal is 1.25 v. 4. these signals are 1.5 v. 5. this signal is 1.8 v. 6. v cc core is the power supply for the processor core and is described in section 2.6 . vid[3:0,25mv] is described in section 2.6 . v tt is used to terminate the system bus and generate v ref on the motherboard. v ss is system ground. bsel[1:0] is described in section 2.8.2 and section 7.0 . all other signals are described in section 7.0 . 7. this signal is used to control the value of the processor on-die termination resistance. refer to the platform design guide for the recommended pulldown resistor value. 8. these signals are 3.3 v. 9. these signals are 2.0 v. 10. 1.25 v signal for differential clock application and 2.5 v for single-ended clock application. 2.8.1 asynchronous vs. synchronous for system bus signals all agtl signals are synchronous to bclk (bclk/bclk#). all of the cmos, clock, apic, and tap signals can be applied asynchronously to bclk (bclk/bclk#). all apic signals are synchronous to picclk. all tap signals are synchronous to tck. table 4. system bus signal groups 1 group name signals agtl input bpri#, defer#, reset#, rsp# agtl output prdy# agtl i/o a[35:3]#, ads#, aerr#, ap[1:0]#, berr#, binit#, bnr#, bp[3:2]#, bpm[1:0]#, br0# 2 , d[63:0]#, dbsy#, dep[7:0]#, drdy#, hit#, hitm#, lock#, req[4:0]#, rp#, rs[2:0]#, trdy# cmos input (1.25 v) 3 vtt_pwrgd cmos input (1.5 v) 4 a20m#, flush#, ignne#, init#, lint0/intr, lint1/nmi, preq#, slp#, smi#, stpclk# cmos input (1.8 v) 5 pwrgood cmos output (1.5 v) 4 ferr#, ierr#, thermtrip# cmos output 8 (3.3 v) vid[3:0,25mv], bsel[1:0] system bus clock 10 (1.25 v/2.5 v) bclk0, bclk0# apic clock 9 picclk apic i/o 4 picd[1:0] tap input 4 tck, tdi, tms, trst# tap output 4 tdo power/other 6 cpupres#, dyn_oe, nchtrl, pll[2:1], slewctrl, rttctrl 7 ,thermdn, thermdp, v cc core , v ref , v ss , v tt , reserved,
24 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.8.2 system bus frequency select signals the system bus frequency select signals (bsel [1:0]) are used to select the system bus frequency for the processor. the bsel signals are also used by the chipset and system bus clock generator. the bsel pins for the processor are open drain signals versus opens or shorts found on the previous intel celeron fc-pga processor. refer to table 11 for level specifications for the bsel signals. the bsel signals rely on a 3.3 v pull-up resistor to set the signal to a logic high level. similar to the vid signals described in section 2.6 , the vtt_pwrgd signal also informs the platform that the bsel signals are stable and should be sampled. during power-up, the bsel signals will be in a indeterminate state for a small period of time. the chipset or system bus clock generator should not sample and/or latch the bsel signals until the vtt_pwrgd signal is asserted. the assertion of the vtt_pwrgd signal indicates the bsel signals are stable and are driven to the final state by the processor. refer to figure 14 for power-up timing sequence for the vtt_pwrgd and the bsel signals. table 5 defines the possible combinations of the bsel signals and the frequency associated with each combination. the frequency selection is determined by the processor(s) and driven out to the chipset and system bus clock generator. all system bus agents must operate at the same frequency determined by the processor. the processor operates at 100 mhz system bus frequency based on the system bus specified rating marked on the package. over or under-clocking the system bus frequency outside the specified rating marked on the package is not recommended. figure 7. bsel[1:0] example for a system design table 5. frequency select truth table for bsel[1:0] bsel1 bsel0 frequency 00 reserved 0 1 100 mhz 10 reserved 1 1 reseved processor bsel0 bsel1 chipset clock driver 1 k ? 3.3v 3.3v
datasheet 25 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.9 test access port (tap) connection due to the voltage levels supported by other components in the test access port (tap) logic, it is recommended that the processor be first in the tap chain and followed by any other components within the system. a translation buffer should be used to connect to the rest of the chain unless one of the other components is capable of accepting an input of the appropriate voltage. similar considerations must be made for tck, tms, and trst#. two copies of each signal may be required with each driving a different voltage level. 2.10 maximum ratings table 6 contains processor stress ratings only. functional operation at the absolute maximum and minimum is not implied nor guaranteed. the processor should not receive a clock while subjected to these conditions. functional operating conditions are given in the timing and level tables in section 2.11 through section 2.13 . extended exposure to the maximum ratings may affect device reliability. furthermore, although the processor contains protective circuitry to resist damage from static electric discharge, one should always take precautions to avoid high static voltages or electric fields. notes: 1. input voltage can never exceed v ss +1.78 volts. 2. input voltage can never exceed v ss + 2.08 volts. 3. input voltage can never go below -0.3 v 4. parameter applies to cmos, apic, and tap bus signal groups only. 2.11 processor voltage level specifications the processor voltage level specifications in this section are defined at the pga370 socket pins (bottom side of the motherboard). see section 7.0 for the processor signal descriptions and section 5.4 for the signal listings. most of the signals on the processor system bus are in the agtl signal group. these signals are specified to be terminated to 1.25 v. the voltage level specifications for these signals are listed in table 10 on page 29 . to allow connection with other devices, the clock, cmos, apic, and tap signals are designed to interface at non-agtl levels. the voltage level specifications for these pins are listed in table 11 on page 29 . table 6. absolute maximum ratings symbol parameter min max unit notes t storage processor storage temperature -40 85 c v cc core and v tt processor core voltage and termination supply voltage with respect to v ss 0.5 1.75 v v in agtl agtl buffer input voltage -0.3 1.78 v 1, 3 v in cmos 1.5 cmos buffer dc input voltage with respect to v ss -0.3 2.08 v 2, 3, 4 v vid & v bsel max vid and bsel pin current -0.3 3.6 v
26 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process table 7 through table 13 list the voltage level specifications for the processor. specifications are valid only while meeting specifications for junction temperature, clock frequency, and input voltages. care should be taken to read all notes associated with each parameter. table 7. voltage and current specifications (sheet 1 of 2) symbol parameter core freq min typ max unit notes 1, 2 v cc core v cc for processor core 1.4 ghz 1.30 ghz 1.20 ghz 1.20 14 ghz 1.10a ghz 1a ghz 900 mhz 1.5 1.5 1.5 1.475 1.475 1.475 1.475 v3, 13 v tt static agtl bus termination voltage 1.25 v 1.25 3% , 4 v tt transient agtl bus termination voltage 1.25 v 1.25 9% , 4 v cc_cmos1.5 1.5 v 1.5 10% , 12 v cc_cmos1.8 1.8 v 1.8 10% , 12 baseboard v cc core tolerance, static processor core voltage static tolerance level at the pga370 socket pins refer to figure 8 and table 9 for tolerance values v5 baseboard v cc core tolerance, transient processor core voltage transient tolerance level at the pga370 socket pins v5 i cc core i cc for processor core 1.4 ghz 1.30 ghz 1.20 ghz 1.20 14 ghz 1.10a ghz 1a ghz 900 mhz 22.6 22.5 21.5 20.6 19.9 19.1 18.1 a6, 13 i cc cmos1.5 i cc for vcc cmos1.5 250 ma i cc cmos1.8 i cc for vcc cmos1.8 1ma i cc cmos3.3 i cc for vcc cmos3.3 35 ma iv tt termination voltage supply current 2.3 a i sgnt i cc stop-grant for processor core 15.37 a 7, 8 i dslp i cc deep sleep 1.4 ghz 1.30 ghz 1.20 ghz 1.20 14 ghz 1.1a ghz 1a ghz 900 mhz 12.0 12.0 12.0 11.0 11.0 11.0 11.0 a di cc core /dt power supply current slew rate refer to table 8 for slew rate a/s 8, 9, 10, 11
datasheet 27 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process notes: 1. unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. all specifications in this table apply only to the celeron processor based on 0.13 micron process core. 3. vcc core and icc core supply the processor core and the on-die l2 cache. 4. v tt must be held to 1.25 v 9% while the agtl bus is active. it is required that v tt be held to 1.25 v 3% while the processor system bus is static (idle condition). the 3% range is the required design target; 9% will come from the transient noise added. this is measured at the pga370 socket pins on the bottom side of the baseboard. 5. these are the tolerance requirements, across a 20 mhz frequency bandwidth, measured at the processor socket pin on the soldered-side of the motherboard. v cc core must return to within the static voltage specification within 100 s after a transient event; see the vrm 8.5 dc-dc converter design guidelines for further details. 6. maximum i cc is measured at v cc typical voltage and under a maximum signal loading conditions. 7. the current specified is also for autohalt state. 8. maximum values are specified by design/characterization at nominal vcc core . 9. based on simulation and averaged over the duration of any change in current. use to compute the maximum inductance tolerable and reaction time of the voltage regulator. this parameter is not tested. 10. dicc/dt specifications are measured and specified at the pga370 socket pins. 11. static voltage regulation includes: dc output initial voltage set point adjust, output ripple and noise, output load ranges specified in the tables above. see vrm 8.5 specification. 12.pull ups only. 13. for frequencies beyond 1.40 ghz, refer to the latest flexible motherboard 1 extended (fmb1-e) guidelines available via your intel representative. 14. 1.20 ghz at vcc core = 1.475 volts and s-spec number sl5xs. table 8 contains typical slew rate data for the processor. actual slew rate values and wave-shapes may vary slightly depending on the type and size of decoupling capacitors used in a particular implementation. di v tt /dt termination current slew rate table 13 a/s 8, 9, 10 see table 13 table 7. voltage and current specifications (sheet 2 of 2) symbol parameter core freq min typ max unit notes 1, 2 table 8. power supply current slew rate (dicc core /dt) 0 5 10 15 20 25 30 0123456 icc @ soc k e t (a) slew rate: 26 a load step slew rate (26 a): icc at socket time (us) icc at socket (a) 0.1 26.23 0.15 23.18 0.5 20.03 1 21.10 1.5 21.88 2 22.29 2.5 22.30 4 22.07 3.5 21.78 4 21.58 4.5 21.51 pwl slew rate data
28 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process table 9. vcc static & transient tolerance icc (a) voltage deviation from vid setting (mv) static tolerance transient tolerance min max min max 01565585 2 5 55 -5 74 4 -5 45 -15 62 6 -15 35 -25 51 8 -25 25 -35 40 10 -35 15 -45 28 12 -45 5 -55 17 14 -55 -5 -65 6 16 -65 -15 -76 -5 18 -75 -25 -87 -15 20 -85 -35 -98 -25 22 -95 -45 -110 -35 24 -105 -55 -121 -45 26 -115 -65 -132 -55 28 -125 -75 -144 -65 30 -135 -85 -155 -75 figure 8. vcc static and transient tolerance -40 -80 -60 -100 -120 -140 -20 0 20 40 60 0 5 10 15 20 25 30 vcc droop from vid setting (mv) icc load (a) 80 transient maximum load line static maximum load line transient minimum load line static minimum load line
datasheet 29 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process notes: 1. unless otherwise noted, all specifications in this table apply to the processor at a frequency up to 1.40 ghz on 0.13 micron. 2. all inputs, outputs, and i/o pins must comply with the signal quality specifications in section 3.0 . 3. minimum and maximum v tt are given in table 13 on page 30 . 4. (0 v in 1.25 v +3%) and (0 v out 1.25 v+3%). 5. refer to the processor i/o buffer models for i/v characteristics. 6. steady state input voltage must not be above v ss + 1.65 v or below v tt ? 1.65 v. 7. does not apply to vcc leakage current due to the presence of on-die rtt. notes: 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz frequency on 0.13 micron. 2. parameter measured at 9 ma (for use with ttl inputs). 3. (0 v in 1.8 v +10%). 4. (0 v out 1.8 v +10%). 5. for bclk specifications, refer to table 24 on page 41 . 6. (0 v in 1.5 v +10%). 7. (0 v out 1.5 v +10%). 8. applies to non-agtl signal pwrgood. 9. applies to non-agtl signal picclk. 10.applies to non-agtl signals except bclk, picclk, and pwrgood. 11.applies to non-agtl signal vtt_pwrgd. 12.vcmos_ref = 2/3 vcc_cmos1.5, refer to table 7 on page 26 . 13.applies to picd[1:0] only table 10. agtl signal group levels specifications symbol parameter min max unit notes 1 v il input low voltage v ref - 0.200 v 6 v ih input high voltage v ref + 0.200 v 2, 3, 6 ron buffer on resistance 16.67 ? 5 i l leakage current for inputs, outputs, and i/o 100 a 4, 7 table 11. non-agtl signal group levels specifications symbol parameter min max unit notes 1 v il 1.2 input low voltage 0.4 v 11 v il 1.5 input low voltage ?0.150 vcmos_ref - 0.300 v 10 v il 1.8 input low voltage -0.36 0.36 v 8 v il 2.0 input low voltage -0.40 0.40 v 9 v ih 1.2 input high voltage 1.03 v 11 v ih 1.5 input high voltage vcmos_ref + 0.250 v cc_cmos1.5 + 10% v 6, 10, 12 v ih 1.5picd input high voltage picd[1:0] vcmos_ref + 0.200 2.0 v 12, 13 v ih 1.8 input high voltage 1.44 2.16 v 8 v ih 2.0 input high voltage 1.60 v 9 r on 30 ? 2 v ol output low voltage 0.30 v 7, 9, all outputs are open-drain i ol output low current 10 ma i li input leakage current 100 a 3, 6 i lo output leakage current 100 a 3, 4, 6, 7
30 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.12 agtl system bus specifications it is recommended that the agtl bus be routed in a daisy-chain fashion with termination resistors to v tt . these termination resistors are placed electrically between the ends of the signal traces and the v tt voltage supply. the valid high and low levels are determined by the input buffers using a reference voltage called v ref . refer to the appropriate platform design guide for more information table 13 lists the nominal specification for the agtl termination voltage (v tt ). the agtl reference voltage (v ref ) is generated on the system motherboard and should be set to 2/3 v tt for the processor and other agtl logic. it is important that the baseboard impedance be specified and held to a 15% tolerance, and that the intrinsic trace capacitance for the agtl signal group traces is known and well-controlled. for more details on the agtl buffer specification, see the intel ? pentium ? ii processor developer's manual and ap-585, intel ? pentium ? ii processor agtl guidelines . notes: 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz frequency. 2. the processor for the pga370 socket contain agtl termination resistors on the processor die, except for the reset# input. 3. v tt must be held to 1.25 v 9%. it is required that v tt be held to 1.25 v 3% while the processor system bus is idle (static condition). this is measured at the pga370 socket pins on the bottom side of the baseboard. 4. uni-processor platforms require a 56 ? resistor and dual-processor platforms require a 68 ? resistor. tolerance for on-die rtt is 10% (56 ? , 68 ? resistors). rtt is 15% (100 ? resistors). 5. v ref is generated on the motherboard and should be 2/3 v tt 5% nominally. insure that there is adequate v ref decoupling on the motherboard. table 12. 3.3 volt cmos output signal group dc specifications symbol parameter min max unit notes v nominal voltage 3.45 v 3.3 + 5% v oh output high voltage 0.9 v i lo output leakage current 100 a table 13. processor agtl bus specifications symbol parameter min typ max units notes 1,2 v tt bus termination voltage 1.1375 1.25 v 3 on-die r tt termination resistor 50 56 68 115 ? 4 v ref bus reference voltage 2/3v tt v5
datasheet 31 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 2.13 system bus timing specifications the processor system bus timings specified in this section are defined at the socket pins on the bottom of the motherboard. unless otherwise specified, timings are tested at the processor pins during manufacturing. timings at the processor pins are specified by design characterization. see section 7.0 for the processor signal definitions. table 14 through table 21 list the timing specifications associated with the processor system bus. these specifications are broken into the following categories: table 14 contains the system bus clock specifications for single-ended clock mode operation and table 15 contains the system bus clock specifications for differential clock mode operation. table 17 contains the agtl specifications, table 18 contains the cmos signal group specifications, table 19 contains timings for the reset conditions, table 20 and covers apic bus timing, and table 21 covers tap timing. all processor system bus timing specifications for the agtl signal group are relative to the rising edge of the bclk input. all agtl timings are referenced to v ref for both ?0? and ?1? logic levels unless otherwise specified.. agtl layout guidelines are also available in the appropriate platform design guide. care should be taken to read all notes associated with a particular timing parameter. 7 notes: 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz frequency on 0.13 micron process. 2. period, jitter, offset and skew measured at 1.25 v. 3. measured from 0.5 to 2.0 v. 4. clkref (bclk#) = 1.25 v with 5% dc tolerance. clkref must be generated from a stable source. ac tolerances must be less than -40 db at 1 mhz. 5. bclk high time is measured above 2.0 v. 6. bclk low time is measured below 0.5 v. table 14. system bus timing specifications (single-ended clock) t# parameter 100 mhz unit figure notes 1,4 min max t1: bclk period - average 10.0 10.15 ns 9 2 t1 abs : bclk period - instantaneous minimum 9.75 ns 2 t2: bclk period stability 250 ps 2 t5: bclk rise time 0.4 1.6 ns 10 3 t6: bclk fall time 0.4 1.6 ns 10 3 t3: bclk high time 2.5 ns 10 5 t4: bclk low time 2.4 ns 10 6 t7: bclk input high 2.2 v t8: bclk input low 0.3 v
32 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz frequency on 0.13 micron process. 2. all timings for the agtl signals are referenced at the rising edge of bclk and the falling edge of bclk# at the processor pin. all agtl signal timings (address bus, data bus, etc.) are referenced at 1.00 v at the processor pins. 3. the internal core clock frequency is derived from the processor system bus clock. the system bus clock to core clock ratio is determined during initialization. individual processors will only operate at their specified system bus frequency, 100 mhz. table 16 shows the supported ratios for each processor. 4. due to the difficulty of accurately measuring clock jitter in a system, it is recommended that a clock driver be used that is designed to meet the period stability specification into a test load of 10 to 20 pf. this should be measured at adjacent crossing points of bclk and bclk# which is defined as the rising edge of bclk and the falling edge of bclk# at the processor pin. the jitter present must be accounted for as a component of bclk timing skew between devices. 5. the clock driver?s closed loop jitter bandwidth must be set low to allow any pll-based device to track the jitter created by the clock driver. the ?20 db attenuation point, as measured into a 10 to 20 pf load, should be less than 500 khz. this specification may be ensured by design characterization and/or measured with a spectrum analyzer. see the appropriate clock synthesizer/driver specification for details 6. measurement taken from differential waveform, defined as bclk ? bclk#. 7. rise time is measured from -0.35 to +0.35v and fall time is measured from 0.35 v to -0.35 v. 8. measured at the socket pin. table 15. system bus timing specifications (differential clock) t# parameter 100 mhz unit figure notes 1,2,6 min max t1: bclk period - average 10.0 10.2 ns 9 3, 4 t1 abs : bclk period - instantaneous minimum 9.8 ns 3, 4 t2: bclk period stability 200 ps 5 vcross: crossing point at 1v swing 0.51 0.76 v 9 t5: bclk rise time 175 550 ps 10 7, 8 t6: bclk fall time 175 550 ps 10 7, 8 rise/fall time matching 325 ps bclk duty cycle 45% 55% 4 input high voltage 0.92 1.45 v input low voltage -0.2 0.35 v rising edge ring back 0.35 v falling edge ring back -0.35 v
datasheet 33 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process notes: 1. contact your local intel representative for the latest information on processor frequencies and/or frequency multipliers. 2. while other bus ratios are defined, operation at frequencies other than those listed are not supported by the processor. 3. individual processors will only operate at their specified system bus frequency; 100 mhz. 4. 1.20 ghz at vcc core = 1.475 volts and s-spec number sl5xs. notes: 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz on 0.13 micron process. 2. these specifications are tested during manufacturing. 3. all timings for the agtl signals are referenced to the rising edge of bclk and the falling edge of bclk# at the processor pin. all agtl signal timings (compatibility signals, etc.) are referenced at 0.80 v at the processor pins. 4. valid delay timings for these signals are specified into 50 ? to 1.25 v, v ref at 0.8 v 2% and with 56 ? or 68 ? on-die r tt . 5. a minimum of 3 clocks must be guaranteed between two active-to-inactive transitions of trdy#. 6. reset# can be asserted (active) asynchronously, but must be deasserted synchronously. 7. specification is for a minimum 0.40 v swing from v ref ? 200 mv to v ref + 200 mv. this assumes an edge rate of 0.3v/ns. 8. specification is for a maximum 0.8 v swing from v tt ? 0.8v to v tt . this assumes an edge rate of 3 v/ns. 9. this should be measured after v cc core , v tt , vcc cmos , and bclk (and bclk#) are stable 10.breq signals observe a 1.2 ns minimum setup time. notes: 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz frequency 2. these specifications are tested during manufacturing. 3. these signals may be driven asynchronously. table 16. valid system bus to core frequency ratios 1, 2, 3 processor core frequency bclk frequency (mhz) frequency multiplier 1.4 ghz 1.40 100 14 1.30 1.30 ghz 100 13 1.20 1.20 ghz 100 12 1.20 4 1.20 4 ghz 100 12 1.1a 1.1a ghz 100 11 1a 1a ghz 100 10 900 900 mhz 100 9 table 17. system bus timing specifications (agtl signal group) t# parameter min max unit figure notes 1,2,3 t7: agtl output valid delay 0.40 3.25 ns 11 4 t8: agtl input setup time 1.30 ns 12 5, 6, 7, 10 t9: agtl input hold time 1.00 ns 12 8 t10: reset# pulse width 1.00 ms 13 6, 9 table 18. system bus timing specifications (cmos signal group) t# parameter min max unit figure notes 1 ,2,3,4 t14: cmos input pulse width, except pwrgood 2 bclks 11 active and inactive states t15: pwrgood inactive pulse width 10 bclks 15 5
34 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 4. all cmos outputs shall be asserted for at least 2 system bus clocks. 5. when driven inactive or after v cc core , v tt , v cc cmos , and bclk and bclk# are stable. note: 1. unless otherwise noted, all specifications in this table apply to all the processor up to 1.40 ghz frequency. notes: 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz frequency. 2. these specifications are tested during manufacturing. 3. all timings for the apic i/o signals are referenced to the picclk rising edge at 0.9 v at the processor pins. all apic i/o signal timings are referenced at 1.0 v at the processor pins. 4. referenced to picclk rising edge. 5. for open drain signals, valid delay is synonymous with float delay. 6. valid delay timings for these signals are specified into 150 ? load pulled up to 1.5 v. table 19. system bus timing specifications (reset conditions) 1 t# parameter min max unit figure notes t16: reset configuration signals (a[14:5]#, br0#, init#) setup time 4 bclks 13 before deassertion of reset# t17: reset configuration signals (a[14:5]#, br0#, init#) hold time 2 20 bclks 13 after clock that deasserts reset# table 20. system bus timing specifications (apic clock and apic i/o) 1, 2, 3 t# parameter min max unit figure notes t21: picclk frequency 2.0 33.3 mhz t22: picclk period 30.0 500.0 ns 10 t23: picclk high time 10.5 ns 10 @ > 1.60 v t24: picclk low time 10.5 ns 10 @ < 0.40 v t25: picclk rise time 0.25 3.0 ns 10 (0.40 v ? 1.60 v) t26: picclk fall time 0.25 3.0 ns 10 (1.60 ? 0.40 v) t27: picd[1:0] setup time 8.0 ns 12 4 t28: picd[1:0] hold time 2.5 ns 12 4 t29a: picd[1:0] valid delay (rising edge) 1.5 8.7 ns 11 4, 5, 6 t29b: picd[1:0] valid delay (falling edge) 1.5 12.0 ns 10 4, 5, 6
datasheet 35 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process notes: 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz frequency. 2. all timings for the tap signals are referenced to the tck rising edge at 1.0 v at the processor pins. all tap signal timings (tms, tdi, etc.) are referenced at 1.0 v at the processor pins. 3. these specifications are tested during manufacturing, unless otherwise noted. 4. 1 ns can be added to the maximum tck rise and fall times for every 1 mhz below 16.667 mhz. 5. referenced to tck rising edge. 6. referenced to tck falling edge. 7. valid delay timing for this signal is specified to 1.5 v. 8. non-test outputs and inputs are the normal output or input signals (besides tck, trst#, tdi, tdo, and tms). these timings correspond to the response of these signals due to tap operations. 9. during debug port operation, use the normal specified timings rather than the tap signal timings. 10.not 100% tested. specified by design characterization. table 21. system bus timing specifications (tap connection) t# parameter min max unit figure notes 1,2,3 t30: tck frequency 16.667 mhz t31: tck period 60.0 ns 10 t32: tck high time 25.0 ns 10 vcmos_ref + 0.200 v, 10 t33: tck low time 25.0 ns 10 vcmos_ref ? 0.200 v, 10 t34: tck rise time 5.0 ns 10 (vcmos_ref ? 0.200 v) ? (vcmos_ref + 0.200 v), 4, 10 t35: tck fall time 5.0 ns 10 (vcmos_ref + 0.200 v) ? (vcmos_ref ? 0.200 v), 4, 10 t36: trst# pulse width 40.0 ns 17 asynchronous, 10 t37: tdi, tms setup time 5.0 ns 16 5 t38: tdi, tms hold time 14.0 ns 16 5 t39: tdo valid delay 1.0 10.0 ns 16 6, 7 t40: tdo float delay 25.0 ns 16 6, 7, 10 t41: all non-test outputs valid delay 2.0 25.0 ns 16 6, 8, 9 t42: all non-test inputs setup time 25.0 ns 16 6, 8, 9, 10 t43: all non-test inputs setup time 5.0 ns 16 5, 8, 9 t44: all non-test inputs hold time 13.0 ns 16 5, 8, 9
36 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process notes: 1. all signals, during their invalid states, must be guarded against spurious levels from effecting the platform during processor power-up sequence. 2. configuration input signals include: a[14:5], br0#, init#. for timing of these signals, refer to table 18 and figure 13 . notes: for figure 9 through figure 19 , the following apply: 1. figure 9 through figure 19 are to be used in conjunction with table 14 through table 21 . 2. all timings for the agtl signals at the processor pins are referenced to the rising edge of bclk and the falling edge of bclk# at the crossing point for differential clock mode and to the rising edge of bclk at bclk vref (1.25 v) for single-ended clock mode. all agtl signal timings (address bus, data bus, etc.) are referenced at 2/3v tt at the processor pins. 3. all timings for the apic i/o signals at the processor pins are referenced to the picclk rising edge at 0.9 v. all apic i/o signal timings are referenced at 1.0 v at the processor pins. 4. all timings for the tap signals at the processor pins are referenced to the tck rising edge at 1.0 v. all tap signal timings (tms, tdi, etc.) are referenced at 1.0 v at the processor pins. table 22. platform power-on timings t# parameter min max unit figure notes 2 t45: valid time before vtt_pwrgd 1.0 ms 14 1 t46: valid time before pwrgood 2.0 ms 14 1 t47: reset# inactive to valid outputs 1 bclk 14 1 t48: reset# inactive to drive signals 4 bclk 14 1 figure 9. clock waveform vih bclk# bclk vil vcross tp tp = t1 (bclk period) note: single-ended clock uses bclk only, differential clock uses blck and bclk#
datasheet 37 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process figure 10. bclk/bclk#, picclk, and tck generic clock waveform figure 11. system bus valid delay timings v3 v1 v2 t p t l t h t r t f vringback (rise) vringback (fall) t r = t5, t25, t34, (rise time) t f = t6, t26, t35, (fall time) t h = t3, t23, t32, (high time) t l = t4, t24, t33, (low time) t p = t1, t22, t31 (bclk, tck, picclk period) v1 = bclk is referenced to 0.30v (differential mode), 0.50v (single-ended mode) tck is referenced to vref - 200 mv, picclk is referenced to 0.4v. v2 = bclk is refernced to 0.9v (differental mode), 2.0v (single-ended mode) tck is referenced to vref + 200 mv, picclk is refernced to 1.6v v3 = bclk and blck# crossing point of the rising edge of blck and the falling edge of bclk# (differential mode), bclk i refereced to 1.25v (single-ended mode), picclk is reference to 1.0v, tck is referenced to vcmosref 0v vih diff vil diff bclk signal valid tx v tx tpw tx = t7, t29a, t29b (valid delay) tpw = t14, t15 (pulse width) v = vref for agtl signal group; vcmosref for cmos, apic and tap signal groups bclk# valid note : single-ended clock uses bclk only, differential clock uses bclk and bclk#
38 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process figure 12. system bus setup and hold timings figure 13. system bus reset and configuration timings bclk valid ts v th v cross = crossing point of blck and bclk# ts = t8, t27 (setup time) th = t9, t28 (hold time) v = vref for agtl signal group; 0.75v for apic and tap signal groups v cross bclk# note : single-ended clock uses bclk only, differential clock uses bclk and bclk# t9 = (agtl+ input hold time) t8 = (agtl+ input setup time) t10 = (reset# pulse width) t16 = (reset configuration signals (a[14:5]#, br0#, flush#, init#) setup time) t17 = (reset configuration signals (a[14:5]#, br0#, flush#, init#) hold time) bclk reset# configuration (a[14:5]#, br0#, flush#, int#) bclk# valid t10 t16 t17 t8 t9 note : single-ended clock uses bclk only, differential clock uses bclk and bclk#
datasheet 39 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process figure 14. platform power-on sequence and timings figure 15. power-on reset and configuration timings vtt, vref vcmosref valid valid vid bsel[1:0] t45 vtt_pwrgd vcc_core picclk bclk# bclk valid config active inactive valid valid valid valid active t46 t47 t48 vcc_pwrgd configuration inputs reset# thermtrip# picd[1:0] agtl outputs all other cmos outputs inactive all other inputs t a valid ratio t c t b pwrgood reset# configuration (a20m#, ignne#, intr, nmi) t a = t15 (pwrgood inactive pulse) t b = t10 (reset# pulse width) t c = t20 (reset configuration signals (a20m#, ignne#, lint[1:0]) hold time) bclk v il, max v ih, min vcc core , v tt , v ref
40 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process figure 16. test timings (tap connection) figure 17. test reset timings t r = t43 (all non-test inputs setup time) t s = t44 (all non-test inputs hold time) t u = t40 (tdo float delay) t v = t37 (tdi, tms setup time) t w = t38 (tdi, tms hold time) t x = t39 (tdo valid delay) t y = t41 (all non-test outputs valid delay) t z = t42 (all non-test outputs float time) t v t w t r t s t u t z t x t y tck tdi, tms input signal tdo output signal t36 trst# t36 = trst# pulse width 1.00v
datasheet 41 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 3.0 signal quality specifications signals driven on the processor system bus should meet signal quality specifications to ensure that the components read data properly and to ensure that incoming signals do not affect the long term reliability of the component. specifications are provided for simulation at the processor pins. meeting the specifications at the processor pins in table 23 , table 24 , and table 27 ensures that signal quality effects will not adversely affect processor operation. 3.1 bclk/bclk# & picclk signal quality specifications and measurement guidelines table 24 describes the signal quality specifications at the processor pins for the processor system bus clock (bclk/bclk#) and apic clock (picclk) signals. references made to bclk signal quality specifications also applies to bclk#. figure 18 describes the signal quality waveform for the system bus clock at the processor pins. notes: 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz frequency. 2. the rising and falling edge ringback voltage specified is the minimum (rising) or maximum (falling) absolute voltage the bclk/bclk# and picclk signals can dip back to after passing the v ih (rising) or v il (falling) voltage limits. this specification is an absolute value. table 23. bclk (single-ended clock mode) signal quality specifications for simulation at the processor pins t# parameter min nom max unit figure notes 1 v1: bclk v il 0.3 v 18 v2: bclk v ih 2.2 v 18 v3: bclk absolute voltage range -0.5 3.1 v 18 v4: bclk rising edge ringback 2.0 v 18 2 v5: bclk falling edge ringback 0.5 v 18 2 table 24. bclk/bclk# (differential clock mode) and picclk signal quality specifications for simulation at the processor pins t# parameter min nom max unit figure notes 1 v1: bclk v il -0.2 0.35 v 18 v1: picclk v il 0.40 v 18 v2: bclk v ih 0.92 1.45 v 18 v2 picclk v ih 1.60 v 18 v3: bclk absolute voltage range -0.2 1.45 v 18 v3: picclk absolute voltage range -0.4 2.4 v 18 v4: bclk rising edge ringback 0.35 v 18 2 v4: picclk rising edge ringback 1.60 v 18 2 v5: bclk falling edge ringback -0.35 v 18 2 v5: picclk falling edge ringback 0.40 v 18 2
42 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 3.2 agtl signal quality specifications and measurement guidelines many scenarios have been simulated to generate a set of agtl layout guidelines which are available in the appropriate platform design guide. refer to the intel ? pentium ? ii processor developer's manual (order number 243502) for the agtl buffer specification. table 25 provides the agtl signal quality specifications for the processor for use in simulating signal quality at the processor pins. the processor maximum allowable overshoot and undershoot specifications for a given duration of time are detailed in table 24 through table 26 . figure 19 shows the agtl ringback tolerance and figure 20 shows the overshoot/undershoot waveform. notes: 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz frequency. 2. specifications are for the edge rate of 0.3 ? 3 v/ns. s ee figure 19 for the generic waveform. 3. all values specified by design characterization. 4. see table 24 for maximum allowable overshoot. 5. ringback between v ref + 100 mv and v ref + 200 mv or v ref ? 300 mv and v ref ? 100 mvs requires the flight time measurements to be adjusted as described in the intel agtl specifications. ringback below v ref + 100 mv or above v ref ? 100 mv is not supported. 6. intel recommends simulations not exceed a ringback value of v ref 200 mv to allow margin for other sources of system noise. 7. a negative value for indicates that the amplitude of ringback is above v ref . (i.e., = -100 mv specifies the signal cannot ringback below v ref + 100 mv). 8. and : are measured relative to v ref . : is measured relative to v ref + 200 mv. figure 18. bclk/bclk#, picclk generic clock waveform at the processor pins v2 v1 v3 v3 v4 v5 table 25. agtl signal groups ringback tolerance specifications at the processor pins t# parameter min unit figure notes 1,2,3 : overshoot 100 mv 19 4, 8 : minimum time at high 0.50 ns 19 : amplitude of ringback 200 mv 19 5, 6, 7, 8 : final settling voltage 200 mv 19 8 : duration of squarewave ringback n/a ns 19
datasheet 43 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 3.2.1 overshoot/undershoot guidelines overshoot (or undershoot) is the absolute value of the maximum voltage above the nominal high voltage or below v ss . the overshoot guideline limits transitions beyond v cc or v ss due to the fast signal edge rates. the processor can be damaged by repeated overshoot events on 1.25 v or 2.5 v tolerant buffers if the charge is large enough (i.e., if the overshoot is great enough). determining the impact of an overshoot/undershoot condition requires knowledge of the magnitude, the pulse direction and the activity factor (af). permanent damage to the processor is the likely result of excessive overshoot/undershoot. violating the overshoot/undershoot guideline will also make satisfying the ringback specification difficult. when performing simulations to determine impact of overshoot and undershoot, esd diodes must be properly characterized. esd protection diodes do not act as voltage clamps and will not provide overshoot or undershoot protection. esd diodes modeled within intel i/o buffer models do not clamp undershoot or overshoot and will yield correct simulation results. if other i/o buffer models are being used to characterize the processor performance, care must be taken to ensure that esd models do not clamp extreme voltage levels. intel i/o buffer models also contain i/o capacitance characterization. therefore, removing the esd diodes from an i/o buffer model will impact results and may yield excessive overshoot/undershoot. figure 19. low to high agtl receiver ringback tolerance ibk tl 0.7v clk ref clock time v start v ref - 0.2 v ref v ref + 0.2 note: high to low case is analogous
44 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 3.2.2 overshoot/undershoot magnitude magnitude describes the maximum potential difference between a signal and its voltage reference level, v ss (overshoot) and v tt (undershoot). while overshoot can be measured relative to v ss using one probe (probe to signal and gnd lead to v ss ), undershoot must be measured relative to v tt . this could be accomplished by simultaneously measuring the v tt plane while measuring the signal undershoot. today?s oscilloscopes can easily calculate the true undershoot waveform. the true undershoot waveform can also be obtained with the following oscilloscope data file analysis: converted undershoot waveform = v tt - signal_measured note: the converted undershoot waveform appears as a positive (overshoot) signal. note: overshoot (rising edge) and undershoot (falling edge) conditions are separate and their impact must be determined independently. after the true waveform conversion, the undershoot/overshoot specifications shown in table 26 through table 29 can be applied to the converted undershoot waveform using the same magnitude and pulse duration specifications used with an overshoot waveform. overshoot/undershoot magnitude levels must observe the absolute maximum specifications listed in table 26 through table 29 . these specifications must not be violated at any time regardless of bus activity or system state. within these specifications are threshold levels that define different allowed pulse durations. provided that the magnitude of the overshoot/undershoot is within the absolute maximum specifications (1.78 v agtl, 2.08 v cmos), the pulse magnitude, duration and activity factor must all be used to determine if the overshoot/undershoot pulse is within specifications. 3.2.3 overshoot/undershoot pulse duration pulse duration describes the total time an overshoot/undershoot event exceeds the overshoot/ undershoot reference voltage (vos_ref = 1.32 v agtl, 1.80 v cmos). the total time could encompass several oscillations above the reference voltage. multiple overshoot/undershoot pulses within a single overshoot/undershoot event may need to be measured to determine the total pulse duration. note: oscillations below the reference voltage can not be subtracted from the total overshoot/undershoot pulse duration. note: multiple overshoot/undershoot events occurring within the same clock cycle must be considered together as one event. using the worst case overshoot/undershoot magnitude, sum together the individual pulse durations to determine the total overshoot/undershoot pulse duration for that total event. 3.2.4 activity factor activity factor (af) describes the frequency of overshoot (or undershoot) occurrence relative to a clock. since the highest frequency of assertion of an agtl or a cmos signal is every other clock, an af = 1 indicates that the specific overshoot (or undershoot) waveform occurs every other clock cycle. thus, an af = 0.01 indicates that the specific overshoot (or undershoot) waveform occurs one time in every 200 clock cycles. the specifications provided in table 26 through table 29 show the maximum pulse duration allowed for a given overshoot/undershoot magnitude at a specific activity factor. each table entry is independent of all others, meaning that the pulse duration reflects the existence of overshoot/undershoot events of that magnitude only. a platform with an overshoot/undershoot
datasheet 45 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process that just meets the pulse duration for a specific magnitude where the af < 1, means that there can be no other overshoot/undershoot events, even of lesser magnitude (note that if af = 1, then the event occurs at all times and no other events can occur). note: activity factor for agtl signals is referenced to system bus clock frequency. note: activity factor for cmos signals is referenced to picclk frequency. 3.2.5 reading overshoot/undershoot specification tables the overshoot/undershoot specification for the processor is not a simple single value. instead, many factors are needed to determine what the over/undershoot specification is. in addition to the magnitude of the overshoot, the following parameters must also be known: the junction temperature the processor will be operating at, the width of the overshoot (as measured above tbd v) and the activity factor (af). to determine the allowed overshoot for a particular overshoot event, the following must be done: 1. determine the signal group that particular signal falls into. if the signal is an agtl signal operating with a 100 mhz system bus, use table 27 (100 mhz agtl signal group). if the signal is a cmos signal, use table 28 (33 mhz cmos signal group). 2. determine the maximum case temperature (tcase) for the range of processors that the system will support (65 o c). 3. determine the magnitude of the overshoot (relative to v ss ) 4. determine the activity factor (how often does this overshoot occur?) 5. from the appropriate specification table, read off the maximum pulse duration (in ns) allowed. 6. compare the specified maximum pulse duration to the signal being measured. if the pulse duration measured is less than the pulse duration shown in the table, then the signal meets the specifications. the above procedure is similar for undershoots after the undershoot waveform has been converted to look like an overshoot. undershoot events must be analyzed separately from overshoot events as they are mutually exclusive. below is an example showing how the maximum pulse duration is determined for a given waveform. given the above parameters, and using table 27 (65 o c/af = 0.1 column) the maximum allowed pulse duration is 7.5 ns. since the measure pulse duration is 7.5 ns, this particular overshoot event passes the overshoot specifications, although this doesn't guarantee that the combined overshoot/ undershoot events meet the specifications. table 26. example platform information required information maximum platform support notes psb signal group 100 mhz agtl max tcase 72 c overshoot magnitude 1.78 v measured value activity factor (af) 0.1 measured overshoot occurs on average every 20 clocks
46 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 3.2.6 determining if a system meets the overshoot/undershoot specifications the overshoot/undershoot specifications listed in the following tables specify the allowable overshoot/undershoot for a single overshoot/undershoot event. however most systems will have multiple overshoot and/or undershoot events that each have their own set of parameters (duration, af and magnitude). while each overshoot on its own may meet the overshoot specification, when you add the total impact of all overshoot events, the system may fail. a guideline to ensure a system passes the overshoot and undershoot specifications is shown below. it is important to meet these guidelines; otherwise, contact your intel field representative. 1. insure no agtl signal ever exceeds 1.78 v and no cmos signal ever exceeds 2.08 v. or 2. if only one overshoot/undershoot event magnitude occurs, ensure it meets the over/undershoot specifications in the following tables or 3. if multiple overshoots and/or multiple undershoots occur, measure the worst case pulse duration for each magnitude and compare the results against the af = 1 specifications. if all of these worst case overshoot or undershoot events meet the specifications (measured time < specifications) in the table (where af=1), then the system passes. the following notes apply to table 26 through table 29 . notes: 1. overshoot/undershoot magnitude = 1.78 v(agtl), 2.08 v(cmos) is an absolute value and should never be exceeded 2. overshoot is measured relative to v ss . 3. undershoot is measured relative to v tt 4. overshoot/undershoot pulse duration is measured relative to 1.32 v for agtl and 1.80 v for cmos. 5. rinbacks below v tt can not be subtracted from overshoots/undershoots 6. lesser undershoot does not allocate longer or larger overshoot 7. oem's are encouraged to follow intel provided layout guidelines. consult the layout guidelines provided in the specific platform design guide. 8. all values specified by design characterization notes: 1. measurements taken at the processor socket pins on the solder-side of the motherboard. 2. overshoot/undershoot magnitude = 1.78 v is an absolute value and should never be exceeded. 3. bclk period = 10.0 ns. table 27. 100 mhz agtl signal group overshoot/undershoot tolerance 1, 2, 3 overshoot/ undershoot magnitude (v) maximum pulse duration at tcase = 60 c (ns) maximum pulse duration at tcase = 69 c (ns) maximum pulse duration at tcase = 71 c (ns) maximum pulse duration at tcase = 72 c (ns) af = 0.01 af = 0.1 af = 1 af = 0.01 af = 0.1 af = 1 af = 0.01 af = 0.1 af = 1 af = 0.01 af = 0.1 af = 1 1.78 20 1.5 0.153 8.7 0.87 0.087 6 0.6 0.06 6 0.6 0.06 1.73 20 3.1 0.31 15 2.0 0.20 13 1.3 0.13 12 1.2 0.12 1.68 20 6.8 0.68 15 4.6 0.46 20 2.8 0.28 20 2.7 0.27 1.63 20 14 1.42 15 10 1.0 20 6.0 0.6 20 5.7 0.57 1.58 20 15 2.95 20 15 2.3 20 12.7 1.27 20 12 1.2 1.53 20 15 6.2 20 15 5.0 20 20 2.65 20 20 2.46 1.48 20 15 13.2 20 20 15 20 20 5.45 20 20 5.10
datasheet 47 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 3.3 non-agtl signal quality specifications and measurement guidelines there are three signal quality parameters defined for non-agtl signals: overshoot/undershoot, ringback, and settling limit. all three signal quality parameters are shown in figure 21 for the non- agtl signal group. note: 1. v hi = 1.80 v for all non-agtl signals except for bclk, picclk, and pwrgood. v hi =2.0 v for picclk, and v hi =1.8 v for pwrgood. bclk and picclk signal quality is detailed in section 3.1 . figure 20. maximum acceptable agtl overshoot/undershoot waveform vos_ref 1.78 v max 1.32 v vss time dependent overshoot time dependent undershoot -0.46 v min ab c ab c 0.1 ns 0.3 ns 1 ns 0.1 ns 0.3 ns 1 ns 1.47 v 1.62 v -0.15 v -0.30 v figure 21. non-agtl overshoot/undershoot, settling limit, and ringback 1 undershoot overshoot settling limit settling limit rising-edge ringback falling-edge ringback v lo v ss time v hi
48 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 3.3.1 overshoot/undershoot guidelines overshoot (or undershoot) is the absolute value of the maximum voltage above the nominal high voltage or below v ss . the overshoot guideline limits transitions beyond v cc or v ss due to the fast signal edge rates (see figure 21 for non-agtl signals). the processor can be damaged by repeated overshoot events on 1.25 v or 1.8 v tolerant buffers if the charge is large enough (i.e., if the overshoot is great enough). permanent damage to the processor is the likely result of excessive overshoot/undershoot. violating the overshoot/undershoot guideline will also make satisfying the ringback specification difficult. the overshoot/undershoot guideline is 0.3 v and assumes the absence of diodes on the input. these guidelines should be verified in simulations without the on- chip esd protection diodes present because the diodes will begin clamping the 1.25 v and 2.5 v tolerant signals beginning at approximately 0.7 v above the appropriate supply and 0.7 v below v ss . if signals are not reaching the clamping voltage, this will not be an issue. a system should not rely on the diodes for overshoot/undershoot protection as this will negatively affect the life of the components and make meeting the ringback specification very difficult. note: the undershoot guideline limits transitions exactly as described for the atgl signals. see figure 20 . 3.3.2 ringback specification ringback refers to the amount of reflection seen after a signal has switched. the ringback specification is the voltage that the signal rings back to after achieving its maximum absolute value. see figure 21 for an illustration of ringback. excessive ringback can cause false signal detection or extend the propagation delay. the ringback specification applies to the input pin of each receiving agent. violations of the signal ringback specification are not allowed under any circumstances for non-agtl signals. ringback can be simulated with or without the input protection diodes that can be added to the input buffer model. however, signals that reach the clamping voltage should be evaluated further. see table 29 for the signal ringback specifications for non-agtl signals for simulations at the processor pins. table 28. 33 mhz cmos signal group overshoot/undershoot tolerance overshoot/ undershoot magnitude (v) maximum pulse duration at tcase = 69 c (ns) maximum pulse duration at tcase = 71 c (ns) maximum pulse duration at tcase = 72 c (ns) af = 0.01 af = 0.1 af = 1 af = 0.01 af = 0.1 af = 1 af = 0.01 af = 0.1 af = 1 2.38 35 3.5 0.35 19 1.9 0.19 17 1.7 0.17 2.33 60 8.0 0.8 40 4.0 0.40 36 3.6 0.36 2.28 60 18 1.8 60 8.0 0.80 60 7.7 0.77 2.23 60 41 4.1 60 18 1.80 60 16 1.60 2.18 60 60 9.0 60 37.5 3.75 60 34 3.42 2.13 60 60 21 60 60 8.00 60 60 7.12 2.08 60 60 60 60 60 16.00 60 60 14.5
datasheet 49 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process notes: 1. unless otherwise noted, all specifications in this table apply to the processor up to 1.40 ghz frequency. 2. non-agtl signals except pwrgood. 3.3.3 settling limit guideline settling limit defines the maximum amount of ringing at the receiving pin that a signal must reach before its next transition. the amount allowed is 10% of the total signal swing (v hi ? v lo ) above and below its final value. a signal should be within the settling limits of its final value, when either in its high state or low state, before it transitions again. signals that are not within their settling limit before transitioning are at risk of unwanted oscillations which could jeopardize signal integrity. simulations to verify settling limit may be done either with or without the input protection diodes present. violation of the settling limit guideline is acceptable if simulations of 5 to 10 successive transitions do not show the amplitude of the ringing increasing in the subsequent transitions. 3.4 vtt_pwrgd signal quality specification the vtt_pwrgd signal is an input to the processor used to determine that the v tt power is stable and the vid and bsel signals should be driven to their final state by the processor. to ensure the processor correctly reads this signal, it must meet the following requirement while the signal is in its transition region of 300 mv to 900 mv. also, vtt_pwrgd should only enter the transition region once, after v tt is at nominal values, for the assertion of the signal. amount of noise (glitch) < 100 mv in addition, the vtt_pwrgd signal should have a reasonable transition time through the transition region. a sharp edge on the signal transition will minimize the chance of noise causing a glitch on this signal. intel recommends the following transition time for the vtt_pwrgd signal. transition time (300 mv to 900 mv) 100 us 3.4.1 transition region the transition region covered by this requirement is 300 mv to 900 mv. once the vtt_pwrgd signal is in that voltage range, the processor is more sensitive to noise which may be present on the signal. the transition region when the signal first crosses the 300 mv voltage level and continues until the last time it is below 900 mv. table 29. signal ringback specifications for non-agtl signal simulation at the processor pins input signal group transition maximum ringback (with input diodes present) unit figure non-agtl signals 2 0 1 vcmos_ref + 0.200 v 21 non-agtl signals 2 1 0 vcmos_ref - 0.300 v 21 pwrgood 0 1 1.44 v 21
50 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 3.4.2 transition time the transition time is defined as the time the signal takes to move through the transition region. a 100 microsecond transition time will ensure that the processor receives a good transition edge. 3.4.3 noise the signal quality of the vtt_pwrgd signal is critical to the correct operation of the processor. every effort should be made to ensure this signal is monotonic in the transition region. if noise or glitches are present on this signal, it must be kept to less than 100 mv of a voltage drop from the highest voltage level received to that point. this glitch must remain less than 100 mv until the excursion ends by the voltage returning to the highest voltage previously received. see figure 22 for an example graph of this situation and requirements. figure 22. noise estimation
datasheet 51 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 4.0 thermal specifications and design considerations this chapter provides needed data for designing a thermal solution. however, for the correct thermal measuring processes, refer to intel ? pentium ? iii processor in the fc-pga2, 370-pin package thermal design guidelines (order number 249660). the processor uses flip chip pin grid array packaging technology with a integrated heat spreader and has a case temperature (t case ) specified. 4.1 thermal specifications table 30 provides the thermal design power dissipation and maximum temperatures for the processor. systems should design for the highest possible processor power, even if a processor with a lower thermal dissipation is planned. a thermal solution should be designed to ensure the case temperature never exceeds these specifications. 1. these values are specified at nominal v cc core for the processor pins. 2. processor power includes the power dissipated by the processor core, the l2 cache, and the agtl bus termination. the maximum power for each of these components does not occur simultaneously. 3. processor core power includes only the power dissipated by the core die. 4. for frequencies beyond 1.4 ghz, refer to the latest flexible motherboard 1 extended (fmb1-e) guidelines available via your intel representative. 5. 1.20 ghz at vcc core = 1.475 volts and s-spec number sl5xs. 4.1.1 thermtrip# requirement in the event the processor drives the thermtrip# signal active during valid operation, both the v cc and v tt supplies to the processor must be turned off to prevent thermal runaway of the processor. valid operation refers to the operating conditions where the thermtrip# signal is guaranteed valid. the time required from thermtrip# asserted to v cc rail at 1/2 nominal is 5 s and thermtrip# asserted to v tt rail at 1/2 nominal is 5 s. note: once v cc and v tt supplies are turned off the thermtrip# signal will be deactivated. system logic should ensure no ?unsafe? power cycling occurs due to this deassertion. table 30. processor thermal design power 1 processor processor core frequency l2 cache size (kbytes) processor power 2 (w) maximum t case (c) 1.40 4 1.40 256 34.8 72 1.30 4 1.30 ghz 256 33.4 71 1.20 1.20 ghz 256 32.1 70 1.20 5 1.20 ghz 256 29.9 69 1.10a 1.10a ghz 256 28.9 69 1a 1a ghz 256 27.8 69 900 900 mhz 256 26.3 69 table 31. thermtrip# time requirement power rail power target time required for power drop v cc 1/2 nominal v cc 5 seconds v tt 1/2 nominal v tt 5 seconds
52 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 4.1.2 thermal diode the processor incorporates an on-die diode that may be used to monitor the die temperature (junction temperature). a thermal sensor located on the motherboard, or a stand-alone measurement kit, may monitor the die temperature of the processor for thermal management or instrumentation purposes. table 32 and table 33 provide the diode parameter and interface specifications. the processor uses an integrated heat spreader (ihs) and has a case temperature requirement. please see the intel ? pentium ? iii processor in the fc-pga2, 370-pin package thermal design guidelines document for details on measuring the case temperature. the thermal diode should be used for system thermal management and not determining spec compliance. notes: 1. intel does not support or recommend operation of the thermal diode under reverse bias. 2. characterized at 75 c with a forward bias current of 5 ? 150 a. 3. characterized at 75 c with a forward bias current of 5 ? 300 a. 4. the ideality factor, n, represents the deviation from ideal diode behavior as exemplified by the diode equation: i fw =is(e^ ((vd*q)/(nkt)) - 1), where is = saturation current, q = electronic charge, vd = voltage across the diode, k = boltzmann constant, and t = absolute temperature (kelvin). 5. not 100% tested. specified by design characterization. 4.2 thermal metrology the thermal metrology for the processor in the fc-pga2 package should be followed to evaluate the thermal performance of proposed cooling solutions. the thermal metrology is contained in the intel ? pentium ? iii processor in the fc-pga2, 370-pin package thermal design guidelines. please contact your local intel field office to obtain this document. table 32. thermal diode parameters symbol parameter min typ max unit notes 1 i fw forward bias current 5 n/a 150 a 1 n diode ideality factor 1.001452 1.007152 1.012852 2, 4, 5 i fw forward bias current 5 n/a 300 a 1 n diode ideality factor 1.000807 1.009528 1.018249 3, 4, 5 table 33. thermal diode interface pin name pga370 socket pin # pin description thermdp al31 diode anode (p_junction) thermdn al29 diode cathode (n_junction)
datasheet 53 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 5.0 mechanical specifications the processor uses a fc-pga2 package technology. mechanical specifications for the processor are given in this section. see section 1.1.1 for a complete terminology listing. the processor utilizes a pga370 socket for installation into the motherboard. details on the socket are available in the 370-pin socket (pga370) design guidelines . note: for figure 23 , the following apply: 1. unless otherwise specified, the following drawings are dimensioned in inches. 2. all dimensions provided with tolerances are guaranteed to be met for all normal production product. 3. figures and drawings labeled as ?reference dimensions? are provided for informational purposes only. reference dimensions are extracted from the mechanical design database and are nominal dimensions with no tolerance information applied. reference dimensions are not checked as part of the processor manufacturing. unless noted as such, dimensions in parentheses without tolerances are reference dimensions. 4. drawings are not to scale. 5.1 fc-pga2 mechanical specifications the following figure with package dimensions is provided to aid in the design of heatsink and clip solutions as well as demonstrate where pin-side capacitors will be located on the processor. table 34 includes the measurements for these dimensions in both inches and millimeters. figure 23. package dimensions
54 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process note: capacitors will be placed on the pin-side of the fc-pga2 package in the area defined by g1, g2, and g3. this area is a keepout zone for motherboard designers. for table 35 , the following apply: 1. it is not recommended to use any portion of the processor substrate as a mechanical reference or load bearing surface for thermal solutions. 2. parameters assume uniformly applied loads notes: 1. this specification applies to a uniform and a non-uniform load. 2. this is the maximum static force that can be applied by the heatsink and clip to maintain the heatsink and processor interface. 3. please see socket manufacturer?s force loading specification also to ensure compliance. maximum static loading listed here does not account for the maximum reaction forces on the socket tabs or pins. table 34. the processor package dimensions symbol millimeters inches minimum maximum notes minimum maximum notes a1 2.266 2.690 0.089 0.106 a2 0.980 1.180 0.038 0.047 b1 30.800 31.200 1.212 1.229 b2 30.800 31.200 1.212 1.229 c1 33.000 max 1.299 max c2 33.000 max 1.299 max d 49.428 49.632 1.946 1.954 d1 45.466 45.974 1.790 1.810 g1 0.000 17.780 0.000 0.700 g2 0.000 17.780 0.000 0.700 g3 0.000 0.889 0.000 0.035 h 2.540 nominal 0.100 nominal l 3.048 3.302 0.120 0.130 p 0.431 0.483 0.017 0.019 pin tp 0.508 diametric true position (pin-to-pin) 0.020 diametric true position (pin-to-pin) table 35. processor case loading parameters parameter dynamic (max) 1 static (max) 2,3 unit ihs surface 200 100 lbf ihs edge 125 n/a lbf ihs corner 75 n/a ibf
datasheet 55 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 5.2 recommended mechanical keep-out zones figure 24. volumetric keep-out figure 25. component keep-out
56 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 5.3 processor markings figure 26 shows the processor top-side markings and it is provided to aid in the identification of the celeron processor. table 34 lists the measurements for the package dimensions. figure 26. top side processor markings grp2ln1 grp2ln2 grp1ln1 grp1ln2 production grp1ln1: intel'01 (m)(c)_-_{coo} grp1ln2: {fpo}-{s/n} grp2ln1: {core freq}/{cache size}/{psb}/{vid} grp2ln2: {s-spec here}
datasheet 57 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 5.4 processor signal listing table 36 and table 37 provide the processor pin definitions. the signal locations on the pga370 socket are to be used for signal routing, simulation, and component placement on the baseboard. figure 27 provides a pin-side view of the processor pinout. figure 27. processor pinout vss vcc vss d35 d29 d33 d26 d28 d21 d23 d25 vss vcc vss d31 vcc d43 vcc vss d34 d38 vcc vss d39 d36 vcc d37 d44 vcc vcc d32 d22 rsv d27 vss d42 d45 d49 vss vcc d63 vref1 vss vcc vss vcc vss vcc vss vcc vss vcc vss vcc vss rsv vtt d62 slew ctrl dep6 dep4 vref0 bpm1 bp3 d41 d52 vss vcc vss vcc vss vcc vss vcc vss vcc d40 d59 d55 d54 d58 d50 d56 dep5 dep1 dep0 bpm0 cpupres vcc vss vcc vss vcc vss vcc vss vcc vss vcc binit d51 d47 d48 d57 d46 d53 d60 d61 dep7 dep3 dep2 prdy vss bp2 vtt vtt vcc vss vcc picclk picd0 preq vcc vcc vss rsv picd1 lint1 vcc vss lint0 rsv rsv rsv vss vcc vss nchctrl rsv rsv vcc vss vcc vtt rtt ctrl vtt vss vcc vss pll2 vtt vtt vcc vss vcc bclk#/ clkref vcc vss vcc vss rsv vtt vtt vcc vss vcc vtt vss ferr rsp vcc vss vtt a20m ierr flush vss vcc detect init vss vtt vss pll1 rsv bclk stpclk ignne vss d16 d19 d7 d30 vcc vcc vref2 d24 d13 d20 vss vss d11 d3 d2 d14 vcc vcc d18 d9 d12 d10 vss rsv d17 vref3 d8 d5 vcc vcc d1 d6 d4 d15 vss vss berr vref4 d0 a34 vcc rsv vss a32 rsv a26 vss vss a29 a18 a27 a30 vcc vcc a24 a23 a33 a20 vss vss a31 vref5 a17 a22 vcc vcc a35 a25 vtt a19 vss vss reset a10 a5 a8 a4 bnr req1 req2 vtt rs1 vcc rs0 therm trip slp vcc vss vcc a21 reset2# vcc vss vcc vss vcc vss vcc vss vcc vss vcc vss vcc bsel1 bsel0 smi vid3 vcc vttpwrgd a28 a3 a11 vref6 a14 vtt req0 lock cmosref aerr pwrgd rs2 rsv tms vcc vid25m v rsv vss a15 a13 a9 ap0 vtt a7 req4 req3 vtt hitm hit dbsy thrmdn thrmdp tck vid0 vid2 key vcc vss vcc vss vcc vss vcc vss vcc vss vcc vss vcc vss vcc vss vid1 dyn_oe a12 a16 a6 vtt ap1 vtt bpri defer vtt rp trdy drdy br0 ads trst tdi tdo pin side view an am al ak aj ah ag af ae ad ac ab aa z y x w v u t s r q p n m l k j h g f e d c b a an am al ak aj ah ag af ae ad ac ab aa z y x w v u t s r q p n m l k j h g f e d c b a 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
58 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process table 36. signal listing in order by signal name pin no. pin name signal group ah6 a10# agtl i/o ak10 a11# agtl i/o an5 a12# agtl i/o al7 a13# agtl i/o ak14 a14# agtl i/o al5 a15# agtl i/o an7 a16# agtl i/o ae1 a17# agtl i/o z6 a18# agtl i/o ag3 a19# agtl i/o ac3 a20# agtl i/o ae33 a20m# cmos input aj1 a21# agtl i/o ae3 a22# agtl i/o ab6 a23# agtl i/o ab4 a24# agtl i/o af6 a25# agtl i/o y3 a26# agtl i/o aa1 a27# agtl i/o ak6 a28# agtl i/o z4 a29# agtl i/o ak8 a3# agtl i/o aa3 a30# agtl i/o ad4 a31# agtl i/o x6 a32# agtl i/o ac1 a33# agtl i/o w3 a34# agtl i/o af4 a35# agtl i/o ah12 a4# agtl i/o ah8 a5# agtl i/o an9 a6# agtl i/o al15 a7# agtl i/o ah10 a8# agtl i/o al9 a9# agtl i/o an31 ads# agtl i/o ak24 aerr# agtl i/o al11 ap0# agtl i/o an13 ap1# agtl i/o w37 bclk system bus clock y33 bclk#/clkref system bus clock v4 berr# agtl i/o b36 binit# agtl i/o ah14 bnr# agtl i/o g33 bp2# agtl i/o e37 bp3# agtl i/o c35 bpm0# agtl i/o e35 bpm1# agtl i/o an17 bpri# agtl input an29 br0# agtl i/o x2 reserved agtl i/o aj33 bsel0 3.3v output aj31 bsel1 3.3v output c37 cpupres# power/other w1 d0# agtl i/o t4 d1# agtl i/o q3 d10# agtl i/o m4 d11# agtl i/o q1 d12# agtl i/o l1 d13# agtl i/o n3 d14# agtl i/o u3 d15# agtl i/o h4 d16# agtl i/o r4 d17# agtl i/o p4 d18# agtl i/o h6 d19# agtl i/o n1 d2# agtl i/o l3 d20# agtl i/o g1 d21# agtl i/o f8 d22# agtl i/o g3 d23# agtl i/o k6 d24# agtl i/o e3 d25# agtl i/o e1 d26# agtl i/o f12 d27# agtl i/o a5 d28# agtl i/o a3 d29# agtl i/o m6 d3# agtl i/o j3 d30# agtl i/o c5 d31# agtl i/o f6 d32# agtl i/o table 36. signal listing in order by signal name (continued) pin no. pin name signal group
datasheet 59 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process c1 d33# agtl i/o c7 d34# agtl i/o b2 d35# agtl i/o c9 d36# agtl i/o a9 d37# agtl i/o d8 d38# agtl i/o d10 d39# agtl i/o u1 d4# agtl i/o c15 d40# agtl i/o d14 d41# agtl i/o d12 d42# agtl i/o a7 d43# agtl i/o a11 d44# agtl i/o c11 d45# agtl i/o a21 d46# agtl i/o a15 d47# agtl i/o a17 d48# agtl i/o c13 d49# agtl i/o s3 d5# agtl i/o c25 d50# agtl i/o a13 d51# agtl i/o d16 d52# agtl i/o a23 d53# agtl i/o c21 d54# agtl i/o c19 d55# agtl i/o c27 d56# agtl i/o a19 d57# agtl i/o c23 d58# agtl i/o c17 d59# agtl i/o t6 d6# agtl i/o a25 d60# agtl i/o a27 d61# agtl i/o e25 d62# agtl i/o f16 d63# agtl i/o j1 d7# agtl i/o s1 d8# agtl i/o p6 d9# agtl i/o al27 dbsy# agtl i/o an19 defer# agtl input c33 dep0# agtl i/o table 36. signal listing in order by signal name (continued) pin no. pin name signal group c31 dep1# agtl i/o a33 dep2# agtl i/o a31 dep3# agtl i/o e31 dep4# agtl i/o c29 dep5# agtl i/o e29 dep6# agtl i/o a29 dep7# agtl i/o af36 detect power/other an27 drdy# agtl i/o an3 dyn_oe power/other ac35 ferr# cmos output ae37 flush# cmos input al25 hit# agtl i/o al23 hitm# agtl i/o ae35 ierr# cmos output ag37 ignne# cmos input ag33 init# cmos input am2 key power/other m36 lint0/intr cmos input l37 lint1/nmi cmos input ak20 lock# agtl i/o n37 nchctrl power/other j33 picclk apic clock input j35 picd0 apic i/o l35 picd1 apic i/o w33 pll1 power/other u33 pll2 power/other a35 prdy# agtl output j37 preq# cmos input ak26 pwrgood cmos input ak18 req0# agtl i/o ah16 req1# agtl i/o ah18 req2# agtl i/o al19 req3# agtl i/o al17 req4# agtl i/o ak30 reserved reserved for future use al1 reserved reserved for future use f10 reserved reserved for future use e21 reserved reserved for future use l33 reserved reserved for future use table 36. signal listing in order by signal name (continued) pin no. pin name signal group
60 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process n33 reserved reserved for future use n35 reserved reserved for future use q33 reserved reserved for future use q35 reserved reserved for future use q37 reserved reserved for future use r2 reserved reserved for future use w35 reserved reserved for future use y1 reserved reserved for future use z36 reserved reserved for future use ah4 reset# agtl input aj3 reset2# agtl input an23 rp# agtl i/o ah26 rs0# agtl + input ah22 rs1# agtl input ak28 rs2# agtl input ac37 rsp# agtl input s35 rttctrl power/other e27 slewctrl power/other ah30 slp# cmos input aj35 smi# cmos input ag35 stpclk# cmos input al33 tck tap input an35 tdi tap input an37 tdo tap output al29 thermdn power/other al31 thermdp power/other ah28 thermtrip# cmos output ak32 tms tap input an25 trdy# agtl input an33 trst# tap input aa37 v cc core power/other aa5 v cc core power/other ab2 v cc core power/other ab34 v cc core power/other ad32 v cc core power/other ae5 v cc core power/other af2 v cc core power/other af34 v cc core power/other ah24 v cc core power/other ah32 v cc core power/other table 36. signal listing in order by signal name (continued) pin no. pin name signal group ah36 v cc core power/other aj13 v cc core power/other aj17 v cc core power/other aj21 v cc core power/other aj25 v cc core power/other aj29 v cc core power/other aj5 v cc core power/other aj9 v cc core power/other ak2 v cc core power/other ak34 v cc core power/other am12 v cc core power/other am16 v cc core power/other am20 v cc core power/other am24 v cc core power/other am28 v cc core power/other am32 v cc core power/other am4 v cc core power/other am8 v cc core power/other b10 v cc core power/other b14 v cc core power/other b18 v cc core power/other b22 v cc core power/other b26 v cc core power/other b30 v cc core power/other b34 v cc core power/other b6 v cc core power/other c3 v cc core power/other d20 v cc core power/other d24 v cc core power/other d28 v cc core power/other d32 v cc core power/other d36 v cc core power/other d6 v cc core power/other e13 v cc core power/other e17 v cc core power/other e5 v cc core power/other e9 v cc core power/other f14 v cc core power/other f2 v cc core power/other f22 v cc core power/other table 36. signal listing in order by signal name (continued) pin no. pin name signal group
datasheet 61 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process f26 v cc core power/other f30 v cc core power/other f34 v cc core power/other f4 v cc core power/other h32 v cc core power/other h36 v cc core power/other j5 v cc core power/other k2 v cc core power/other k32 v cc core power/other k34 v cc core power/other m32 v cc core power/other n5 v cc core power/other p2 v cc core power/other p34 v cc core power/other r32 v cc core power/other r36 v cc core power/other s5 v cc core power/other t2 v cc core power/other t34 v cc core power/other v32 v cc core power/other v36 v cc core power/other w5 v cc core power/other y35 v cc core power/other z32 v cc core power/other ak22 v cmos_ref power/other ak36 vid 25mv 3.3v output al35 vid0 3.3v output am36 vid1 3.3v output al37 vid2 3.3v output aj37 vid3 3.3v output e33 v ref 0 power/other f18 v ref 1 power/other k4 v ref 2 power/other r6 v ref 3 power/other v6 v ref 4 power/other ad6 v ref 5 power/other ak12 v ref 6 power/other a37 vss power/other ab32 vss power/other ac33 vss power/other table 36. signal listing in order by signal name (continued) pin no. pin name signal group ac5 vss power/other ad2 vss power/other ad34 vss power/other af32 vss power/other ag5 vss power/other ah2 vss power/other ah34 vss power/other aj11 vss power/other aj15 vss power/other aj19 vss power/other aj23 vss power/other aj27 vss power/other aj7 vss power/other al3 vss power/other am10 vss power/other am14 vss power/other am18 vss power/other am22 vss power/other am26 vss power/other am30 vss power/other am34 vss power/other am6 vss power/other b12 vss power/other b16 vss power/other b20 vss power/other b24 vss power/other b28 vss power/other b32 vss power/other b4 vss power/other b8 vss power/other d18 vss power/other d2 vss power/other d22 vss power/other d26 vss power/other d30 vss power/other d34 vss power/other d4 vss power/other e11 vss power/other e15 vss power/other e19 vss power/other table 36. signal listing in order by signal name (continued) pin no. pin name signal group
62 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process e7 vss power/other f20 vss power/other f24 vss power/other f28 vss power/other f32 vss power/other f36 vss power/other g5 vss power/other h2 vss power/other h34 vss power/other k36 vss power/other l5 vss power/other m2 vss power/other m34 vss power/other p32 vss power/other p36 vss power/other q5 vss power/other r34 vss power/other t32 vss power/other t36 vss power/other u5 vss power/other v2 vss power/other v34 vss power/other x32 vss power/other x36 vss power/other x4 vss power/other table 36. signal listing in order by signal name (continued) pin no. pin name signal group y37 vss power/other y5 vss power/other z2 vss power/other z34 vss power/other ab36 v tt power/other ad36 v tt power/other ag1 v tt power/other ah20 v tt power/other ak16 v tt power/other al13 v tt power/other al21 v tt power/other an11 v tt power/other an15 v tt power/other e23 v tt power/other g35 v tt power/other g37 v tt power/other s33 v tt power/other x34 v tt power/other aa33 v tt power/other aa35 v tt power/other an21 v tt power/other s37 v tt power/other u35 v tt power/other u37 v tt power/other ak4 v tt _pwrgd power/other table 36. signal listing in order by signal name (continued) pin no. pin name signal group
datasheet 63 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process table 37. signal listing in order by pin number pin no. pin name signal group a3 d29# agtl i/o a5 d28# agtl i/o a7 d43# agtl i/o a9 d37# agtl i/o a11 d44# agtl i/o a13 d51# agtl i/o a15 d47# agtl i/o a17 d48# agtl i/o a19 d57# agtl i/o a21 d46# agtl i/o a23 d53# agtl i/o a25 d60# agtl i/o a27 d61# agtl i/o a29 dep7# agtl i/o a31 dep3# agtl i/o a33 dep2# agtl i/o a35 prdy# agtl output a37 vss power/other aa1 a27# agtl i/o aa3 a30# agtl i/o aa5 v cc core power/other aa33 v tt power/other aa35 v tt power/other aa37 v cc core power/other ab2 v cc core power/other ab4 a24# agtl i/o ab6 a23# agtl i/o ab32 vss power/other ab34 v cc core power/other ab36 v tt power/other ac1 a33# agtl i/o ac3 a20# agtl i/o ac5 vss power/other ac33 vss power/other ac35 ferr# cmos output ac37 rsp# agtl input ad2 vss power/other ad4 a31# agtl i/o ad6 v ref 5 power/other ad32 v cc core power/other ad34 vss power/other ad36 v tt power/other ae1 a17# agtl i/o ae3 a22# agtl i/o ae5 v cc core power/other ae33 a20m# cmos input ae35 ierr# cmos output ae37 flush# cmos input af2 v cc core power/other af4 a35# agtl i/o af6 a25# agtl i/o af32 vss power/other af34 v cc core power/other af36 detect power/other ag1 v tt power/other ag3 a19# agtl i/o ag5 vss power/other ag33 init# cmos input ag35 stpclk# cmos input ag37 ignne# cmos input ah2 vss power/other ah4 reset# agtl input ah6 a10# agtl i/o ah8 a5# agtl i/o ah10 a8# agtl i/o ah12 a4# agtl i/o ah14 bnr# agtl i/o ah16 req1# agtl i/o ah18 req2# agtl i/o ah20 v tt power/other ah22 rs1# agtl input ah24 v cc core power/other ah26 rs0# agtl + input ah28 thermtrip# cmos output ah30 slp# cmos input ah32 v cc core power/other ah34 vss power/other ah36 v cc core power/other aj1 a21# agtl i/o aj3 reset2# agtl input table 37. signal listing in order by pin number (continued) pin no. pin name signal group
64 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process aj5 v cc core power/other aj7 vss power/other aj9 v cc core power/other aj11 vss power/other aj13 v cc core power/other aj15 vss power/other aj17 v cc core power/other aj19 vss power/other aj21 v cc core power/other aj23 vss power/other aj25 v cc core power/other aj27 vss power/other aj29 v cc core power/other aj31 bsel1 3.3v output aj33 bsel0 3.3v output aj35 smi# cmos input aj37 vid3 3.3v output ak2 v cc core power/other ak4 v tt _pwrgd power/other ak6 a28# agtl i/o ak8 a3# agtl i/o ak10 a11# agtl i/o ak12 v ref 6 power/other ak14 a14# agtl i/o ak16 v tt power/other ak18 req0# agtl i/o ak20 lock# agtl i/o ak22 v cmos_ref power/other ak24 aerr# agtl i/o ak26 pwrgood cmos input ak28 rs2# agtl input ak30 reserved reserved for future use ak32 tms tap input ak34 v cc core power/other ak36 vid 25mv 3.3v output al1 reserved reserved for future use al3 vss power/other al5 a15# agtl i/o al7 a13# agtl i/o al9 a9# agtl i/o table 37. signal listing in order by pin number (continued) pin no. pin name signal group al11 ap0# agtl i/o al13 v tt power/other al15 a7# agtl i/o al17 req4# agtl i/o al19 req3# agtl i/o al21 v tt power/other al23 hitm# agtl i/o al25 hit# agtl i/o al27 dbsy# agtl i/o al29 thermdn power/other al31 thermdp power/other al33 tck tap input al35 vid0 3.3v output al37 vid2 3.3v output am2 key power/other am4 v cc core power/other am6 vss power/other am8 v cc core power/other am10 vss power/other am12 v cc core power/other am14 vss power/other am16 v cc core power/other am18 vss power/other am20 v cc core power/other am22 vss power/other am24 v cc core power/other am26 vss power/other am28 v cc core power/other am30 vss power/other am32 v cc core power/other am34 vss power/other am36 vid1 3.3v output an3 dyn_oe power/other an5 a12# agtl i/o an7 a16# agtl i/o an9 a6# agtl i/o an11 v tt power/other an13 ap1# agtl i/o an15 v tt power/other an17 bpri# agtl input table 37. signal listing in order by pin number (continued) pin no. pin name signal group
datasheet 65 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process an19 defer# agtl input an21 v tt power/other an23 rp# agtl i/o an25 trdy# agtl input an27 drdy# agtl i/o an29 br0# agtl i/o an31 ads# agtl i/o an33 trst# tap input an35 tdi tap input an37 tdo tap output b2 d35# agtl i/o b4 vss power/other b6 v cc core power/other b8 vss power/other b10 v cc core power/other b12 vss power/other b14 v cc core power/other b16 vss power/other b18 v cc core power/other b20 vss power/other b22 v cc core power/other b24 vss power/other b26 v cc core power/other b28 vss power/other b30 v cc core power/other b32 vss power/other b34 v cc core power/other b36 binit# agtl i/o c1 d33# agtl i/o c3 v cc core power/other c5 d31# agtl i/o c7 d34# agtl i/o c9 d36# agtl i/o c11 d45# agtl i/o c13 d49# agtl i/o c15 d40# agtl i/o c17 d59# agtl i/o c19 d55# agtl i/o c21 d54# agtl i/o c23 d58# agtl i/o table 37. signal listing in order by pin number (continued) pin no. pin name signal group c25 d50# agtl i/o c27 d56# agtl i/o c29 dep5# agtl i/o c31 dep1# agtl i/o c33 dep0# agtl i/o c35 bpm0# agtl i/o c37 cpupres# power/other d2 vss power/other d4 vss power/other d6 v cc core power/other d8 d38# agtl i/o d10 d39# agtl i/o d12 d42# agtl i/o d14 d41# agtl i/o d16 d52# agtl i/o d18 vss power/other d20 v cc core power/other d22 vss power/other d24 v cc core power/other d26 vss power/other d28 v cc core power/other d30 vss power/other d32 v cc core power/other d34 vss power/other d36 v cc core power/other e1 d26# agtl i/o e3 d25# agtl i/o e5 v cc core power/other e7 vss power/other e9 v cc core power/other e11 vss power/other e13 v cc core power/other e15 vss power/other e17 v cc core power/other e19 vss power/other e21 reserved reserved for future use e23 v tt 4 power/other e25 d62# agtl i/o e27 slewctrl power/other e29 dep6# agtl i/o table 37. signal listing in order by pin number (continued) pin no. pin name signal group
66 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process e31 dep4# agtl i/o e33 v ref 0 power/other e35 bpm1# agtl i/o e37 bp3# agtl i/o f2 v cc core power/other f4 v cc core power/other f6 d32# agtl i/o f8 d22# agtl i/o f10 reserved reserved for future use f12 d27# agtl i/o f14 v cc core power/other f16 d63# agtl i/o f18 v ref 1 power/other f20 vss power/other f22 v cc core power/other f24 vss power/other f26 v cc core power/other f28 vss power/other f30 v cc core power/other f32 vss power/other f34 v cc core power/other f36 vss power/other g1 d21# agtl i/o g3 d23# agtl i/o g5 vss power/other g33 bp2# agtl i/o g35 v tt power/other g37 v tt power/other h2 vss power/other h4 d16# agtl i/o h6 d19# agtl i/o h32 v cc core power/other h34 vss power/other h36 v cc core power/other j1 d7# agtl i/o j3 d30# agtl i/o j5 v cc core power/other j33 picclk apic clock input j35 picd0 apic i/o j37 preq# cmos input table 37. signal listing in order by pin number (continued) pin no. pin name signal group k2 v cc core power/other k4 v ref 2 power/other k6 d24# agtl i/o k32 v cc core power/other k34 v cc core power/other k36 vss power/other l1 d13# agtl i/o l3 d20# agtl i/o l5 vss power/other l33 reserved reserved for future use l35 picd1 apic i/o l37 lint1/nmi cmos input m2 vss power/other m4 d11# agtl i/o m6 d3# agtl i/o m32 v cc core power/other m34 vss power/other m36 lint0/intr cmos input n1 d2# agtl i/o n3 d14# agtl i/o n5 v cc core power/other n33 reserved reserved for future use n35 reserved reserved for future use q33 reserved reserved for future use p2 v cc core power/other p4 d18# agtl i/o p6 d9# agtl i/o p32 vss power/other p34 v cc core power/other p36 vss power/other q1 d12# agtl i/o q3 d10# agtl i/o q5 vss power/other n37 nchctrl power/other q35 reserved reserved for future use q37 reserved reserved for future use r2 reserved reserved for future use r4 d17# agtl i/o r6 v ref 3 power/other r32 v cc core power/other table 37. signal listing in order by pin number (continued) pin no. pin name signal group
datasheet 67 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process r34 vss power/other r36 v cc core power/other s1 d8# agtl i/o s3 d5# agtl i/o s5 v cc core power/other s33 v tt power/other s35 rttctrl power/other s37 v tt power/other t2 v cc core power/other t4 d1# agtl i/o t6 d6# agtl i/o t32 vss power/other t34 v cc core power/other t36 vss power/other u1 d4# agtl i/o u3 d15# agtl i/o u5 vss power/other u33 pll2 power/other u35 v tt power/other u37 v tt power/other v2 vss power/other v4 berr# agtl i/o v6 v ref 4 power/other v32 v cc core power/other v34 vss power/other table 37. signal listing in order by pin number (continued) pin no. pin name signal group v36 v cc core power/other w1 d0# agtl i/o w3 a34# agtl i/o w5 v cc core power/other w33 pll1 power/other w35 reserved reserved for future use w37 bclk system bus clock x2 reserved agtl i/o x4 vss power/other x6 a32# agtl i/o x32 vss power/other x34 v tt power/other x36 vss power/other y1 reserved reserved for future use y3 a26# agtl i/o y5 vss power/other y33 bclk#/clkref system bus clock y35 v cc core power/other y37 vss power/other z2 vss power/other z4 a29# agtl i/o z6 a18# agtl i/o z32 v cc core power/other z34 vss power/other z36 reserved reserved for future use table 37. signal listing in order by pin number (continued) pin no. pin name signal group
68 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 6.0 boxed processor specifications the processor for the pga370 socket is also offered as an intel boxed processor. intel boxed processors are intended for system integrators who build systems from motherboards and standard components. the boxed processor will be supplied with an unattached fan heatsink. this section documents motherboard and system requirements for the fan heatsink that will be supplied with the boxed processor. this section is particularly important for oems that manufacture motherboards for system integrators. unless otherwise noted, all figures in this section are dimensioned in inches. figure 28 shows a mechanical representation of the boxed intel processor in the flip chip pin grid array 2 (fc-pga2) package. note: drawings in this section reflect only the specifications on the intel boxed processor product. these dimensions should not be used as a generic keep-out zone for all heatsinks. it is the system designer?s responsibility to consider their proprietary solution when designing to the required keep- out zone on their system platform and chassis. refer to the intel ? pentium ? iii processor thermal/ mechanical functional specification for further guidance. contact your local intel sales representative for this document. 6.1 mechanical specifications 6.1.1 mechanical specifications for the fc-pga2 package this section documents the mechanical specifications of the boxed processor fan heatsink in the fc-pga2 package. the boxed processor in the fc-pga2 package ships with an un-attached fan heatsink. figure 28 shows a mechanical representation of the boxed processor for the pga370 socket in the flip chip pin grid array 2 (fc-pga2) package. the boxed processor fan heatsink is also asymmetrical in that the mechanical step feature, figure 31 , must sit over the socket?s cam. the step allows the heatsink to securely interface with the processor in order to meet the processor?s thermal requirements. figure 28. conceptual boxed processor for the pga370 socket heatsink clip heatsink fan
datasheet 69 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process the dimensions for the boxed processor with the integrated fan heatsink are shown in figure 30 . all dimensions are in inches. the processor uses a new technology termed fc-pga2. the fc-pga2 package leverages the previous fc-pga package technology used on processors based on the 0.18 micron process. the fc-pga2 package adds an integrated heat spreader (ihs) to improve heat conduction from the processor die. this new solution prevent the need for exotic thermal solutions in the higher power density processors. see section 5.0 of this document for the mechanical specifications of the pga370 socket. section 5.2 of this document also shows the recommended mechanical keepout zones for the boxed processor fan heatink assembly. figure 24 and figure 25 show the required keepout dimensions for the boxed processor thermal solution. the cooling fin orientation on the heatsink relative to the pga370 socket is subject to change. contact your local intel sales representative for documentation specific to the boxed fan heatsink orientation relative to the pga370 socket. figure 31 shows the changes to the package mechanicals between the fc-pga and fc-pga2 designs. note that the boxed fan heatsinks and associated clips are not compatible with earlier boxed fan heatsinks for processors based on the 0.18 micron process. figure 29. comparison between fc-pga and fc-pga2 package figure 30. side view of space requirements for the boxed processor 3.2 mm 1.9 mm 49.5 mm square fc-pga fc-pga2 49.5 mm square 3.2 mm 3.5 mm 1.89 3.11 1.76 3.17 1.89 2.65
70 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 6.1.2 boxed processor heatsink weight the boxed processor thermal cooling solution will not weigh more than 180 grams. 6.2 thermal specifications this section describes the cooling requirements of the thermal cooling solution utilized by the boxed processor. 6.2.1 boxed processor cooling requirements the boxed processor is directly cooled with a fan heatsink. however, meeting the processor?s temperature specification is also a function of the thermal design of the entire system and ultimately the responsibility of the system integrator. the processor temperature specification is found in section 4.1 of this document. the boxed processor fan heatsink is able to keep the processor temperature within the specifications (see table 30 in section 4.1 ) in chassis that provide good thermal management. for the boxed processor fan heatsink to operate properly, it is critical that the airflow provided to the fan heatsink is unimpeded. airflow of the fan heatsink is into the center and out of the sides of the fan heatsink. airspace is required around the fan to ensure that the airflow through the fan heatsink is not blocked. blocking the airflow to the fan heatsink reduces the cooling efficiency and decreases fan life. figure 32 illustrate an acceptable airspace clearance for the fan heatsink. it is table 38. boxed processor fan heatsink spatial dimensions dimensions (inches) min typ max units fan heatsink length 3.14 inches fan heatsink height 1.81 inches fan heatsink width 2.6 inches fan heatsink height above motherboard 0.29 0.30 0.33 inches air keepout zones from end of fan heatsink 0.20 inches figure 31. dimensions of mechanical step feature in heatsink base 0.043 0.472 units = inches
datasheet 71 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process also recommended that the air temperature entering the fan be kept below 45 degrees c. again, meeting the processor?s temperature specification is the responsibility of the system integrator. the processor temperature specification is found in section 4.1 of this document. 6.2.2 boxed processor thermal cooling solution clip the boxed processor thermal solution requires installation by a system integrator to secure the thermal cooling solution to the processor after it is installed in the 370-pin socket zif socket. motherboards designed for use by system integrators should take care to consider the implications of clip installation and potential scraping of the motherboard pcb underneath the 370-pin socket attach tabs. motherboard components should not be placed too close to the 370-pin socket attach tabs in a way that interferes with the installation of the boxed processor thermal cooling solution figure 24 and figure 25 show the required keepout dimensions for the boxed processor thermal solution. 6.3 electrical requirements for the boxed processor 6.3.1 electrical requirements the boxed processor's fan heatsink requires a +12 v power supply. a fan power cable is attached to the fan and will draw power from a power header on the motherboard. the power cable connector and pinout are shown in figure 33 . motherboards must provide a matched power header to support the boxed processor. table 38 contains specifications for the input and output signals at the fan heatsink connector. the fan heatsink outputs a sense signal (an open-collector output) that pulses at a rate of two pulses per fan revolution. a motherboard pull-up resistor provides voh to match the motherboard-mounted fan speed monitor requirements, if applicable. use of the sense signal is optional. if the sense signal is not used, pin 3 of the connector should be tied to gnd. the power header on the baseboard must be positioned to allow the fan heatsink power cable to reach it. the power header identification and location should be documented in the motherboard documentation or on the motherboard. figure 34 shows the recommended location of the fan power connector relative to the pga370 socket. the motherboard power header should be positioned within 4.00 inches (lateral) of the fan power connector for the fc-pga2 package. figure 32. thermal airspace requirement for all boxed processor fan heatsinks in the pga370 socket measure ambient temperature 0.3 inches above center of fan inlet fan heatsink 0.20 inches min. air space processor pga-370 socket 0.20 inches min. air space
72 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process figure 33. boxed processor fan heatsink power cable connector description table 39. fan heatsink power and signal specifications description min typ max +12 v: 12 volt fan power supply 10.8 v 12 v 13.2 v ic: fan current draw 100 ma sense: sense frequency (motherboard should pull this pin up to appropriate v cc with resistor) 2 pulses per fan revolution figure 34. motherboard power header placement relative to the boxed processor pin signal straight square pin, 3-pin terminal housing with polarizing ribs and friction locking ramp. 0.100" pin pitch, 0.025" square pin width. waldom/molex p/n 22-01-3037 or equivalent. match with straight pin, friction lock header on motherboard waldom/molex p/n 22-23-2031, amp p/n 640456-3, or equivalent. 1 2 3 gnd +12v sense 12 3 0.10" socket 7 0.10" r = 4.00? pga370
datasheet 73 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 7.0 processor signal description this section provides an alphabetical listing of all the processor signals. the tables at the end of this section summarize the signals by direction: output, input, and i/o. 7.1 alphabetical signals reference table 40. signal description (sheet 1 of 8) name type description a20m# i if the a20m# (address-20 mask) input signal is asserted, the processor masks physical address bit 20 (a20#) before looking up a line in any internal cache and before driving a read/write transaction on the bus. asserting a20m# emulates the 8086 processor's address wrap-around at the 1 mb boundary. assertion of a20m# is only supported in real mode. a20m# is an asynchronous signal. however, to ensure recognition of this signal following an i/o write instruction, it must be valid along with the trdy# assertion of the corresponding i/o write bus transaction. a[35:3]# i/o the a[35:3]# (address) signals define a 2 36 -byte physical memory address space. when ads# is active, these pins transmit the address of a transaction; when ads# is inactive, these pins transmit transaction type information. these signals must connect the appropriate pins of all agents on the processor system bus. the a[35:24]# signals are parity-protected by the ap1# parity signal, and the a[23:3]# signals are parity-protected by the ap0# parity signal. on the active-to-inactive transition of reset#, the processors sample the a[35:3]# pins to determine their power-on configuration. see the intel ? pentium ? ii processor developer?s manual for details. ads# i/o the ads# (address strobe) signal is asserted to indicate the validity of the transaction address on the a[35:3]# pins. all bus agents observe the ads# activation to begin parity checking, protocol checking, address decode, internal snoop, or deferred reply id match operations associated with the new transaction. this signal must connect the appropriate pins on all processor system bus agents. aerr# i/o the aerr# (address parity error) signal is observed and driven by all processor system bus agents, and if used, must connect the appropriate pins on all processor system bus agents. aerr# observation is optionally enabled during power-on configuration; if enabled, a valid assertion of aerr# aborts the current transaction. if aerr# observation is disabled during power-on configuration, a central agent may handle an assertion of aerr# as appropriate to the error handling architecture of the system. ap[1:0]# i/o the ap[1:0]# (address parity) signals are driven by the request initiator along with ads#, a[35:3]#, req[4:0]#, and rp#. ap1# covers a[35:24]#, and ap0# covers a[23:3]#. a correct parity signal is high if an even number of covered signals are low and low if an odd number of covered signals are low. this allows parity to be high when all the covered signals are high. ap[1:0]# should connect the appropriate pins of all processor system bus agents. bclk/bclk# i the bclk (bus clock) and bclk# (for differential clock) signals determines the bus frequency. all processor system bus agents must receive this signal to drive their outputs and latch their inputs on the rising edge of bclk. for differential clocking, all processor system bus agents must receive this signal to drive their outputs and latch their inputs on the bclk and bclk# crossing point. all external timing parameters are specified with respect to the bclk signal.
74 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process berr# i/o the berr# (bus error) signal is asserted to indicate an unrecoverable error without a bus protocol violation. it may be driven by all processor system bus agents, and must connect the appropriate pins of all such agents, if used. however, the processor does not observe assertions of the berr# signal. berr# assertion conditions are configurable at a system level. assertion options are defined by the following options: ? enabled or disabled. ? asserted optionally for internal errors along with ierr#. ? asserted optionally by the request initiator of a bus transaction after it observes an error. ? asserted by any bus agent when it observes an error in a bus transaction. binit# i/o the binit# (bus initialization) signal may be observed and driven by all processor system bus agents, and if used must connect the appropriate pins of all such agents. if the binit# driver is enabled during power on configuration, binit# is asserted to signal any bus condition that prevents reliable future information. if binit# observation is enabled during power-on configuration, and binit# is sampled asserted, all bus state machines are reset and any data which was in transit is lost. all agents reset their rotating id for bus arbitration to the state after reset, and internal count information is lost. the l1 and l2 caches are not affected. if binit# observation is disabled during power-on configuration, a central agent may handle an assertion of binit# as appropriate to the error handling architecture of the system. bnr# i/o the bnr# (block next request) signal is used to assert a bus stall by any bus agent who is unable to accept new bus transactions. during a bus stall, the current bus owner cannot issue any new transactions. since multiple agents might need to request a bus stall at the same time, bnr# is a wire-or signal which must connect the appropriate pins of all processor system bus agents. in order to avoid wire-or glitches associated with simultaneous edge transitions driven by multiple drivers, bnr# is activated on specific clock edges and sampled on specific clock edges. bp[3:2]# i/o the bp[3:2]# (breakpoint) signals are outputs from the processor that indicate the status of breakpoints. bpm[1:0]# i/o the bpm[1:0]# (breakpoint monitor) signals are breakpoint and performance monitor signals. they are outputs from the processor which indicate the status of breakpoints and programmable counters used for monitoring processor performance. bpri# i the bpri# (bus priority request) signal is used to arbitrate for ownership of the processor system bus. it must connect the appropriate pins of all processor system bus agents. observing bpri# active (as asserted by the priority agent) causes all other agents to stop issuing new requests, unless such requests are part of an ongoing locked operation. the priority agent keeps bpri# asserted until all of its requests are completed, then releases the bus by deasserting bpri#. br0# i/o the br0# (bus request) pins drive the breq[0]# signal in the system. during power-up configuration, the central agent asserts the br0# bus signal in the system to assign the symmetric agent id to the processor. the processor samples its br0# pin on the active-to-inactive transition of the reset# to obtain its symmetric agent id. the processor asserts the br0# pin to request the system bus. br0# must be connected to a 10-56 ? resistor to v ss . refer to the platform design guide for implementation detail and resistor tolerance. table 40. signal description (sheet 2 of 8) name type description
datasheet 75 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process bsel[1:0] o the bsel signals are cmos signals which are used to select the system bus frequency. a bsel[1:0] = ?01? selects a 100 mhz system bus frequency. the frequency is determined by the processor(s), chipset, and frequency synthesizer capabilities. all system bus agents must operate at the same frequency. the processor operates at 100 mhz system bus frequency. these signals must be pulled up to 3.3v power rail with 330 ? ? 1 k ? resistors and provided as a frequency selection signal to the clock driver/synthesizer and chipset. refer to the platform design guide for implementation detail and resistor tolerance. clkref i in single-ended clock mode the clkref input is a filtered 1.25v supply voltage for the processor pll. a voltage divider and decoupling solution is provided by the motherboard. see the design guide for implementation details. when the processor operates in differential clock mode, this signal becomes bclk#. cpupres# o the cpupres# signal is defined to allow a system design to detect the presence of a processor in a pga370 socket. combined with the vid combination of vid[25mv,3:0]= 11111 (see section 2.6 ), a system can determine if a socket is occupied, and whether a processor core is present. see the table below for states and values for determining the presence of a device. d[63:0]# i/o the d[63:0]# (data) signals are the data signals. these signals provide a 64-bit data path between the processor system bus agents, and must connect the appropriate pins on all such agents. the data driver asserts drdy# to indicate a valid data transfer. dbsy# i/o the dbsy# (data bus busy) signal is asserted by the agent responsible for driving data on the processor system bus to indicate that the data bus is in use. the data bus is released after dbsy# is deasserted. this signal must connect the appropriate pins on all processor system bus agents. defer# i the defer# signal is asserted by an agent to indicate that a transaction cannot be guaranteed in-order completion. assertion of defer# is normally the responsibility of the addressed memory or i/o agent. this signal must connect the appropriate pins of all processor system bus agents. dep[7:0]# i/o the dep[7:0]# (data bus ecc protection) signals provide optional ecc protection for the data bus. they are driven by the agent responsible for driving d[63:0]#, and must connect the appropriate pins of all processor system bus agents which use them. the dep[7:0]# signals are enabled or disabled for ecc protection during power on configuration. detect o a tri-state (high-impedance) output. can be used for platforms that need to differentiate the previous generation intel celeron processors for the pga370 socket that support v tt = 1.50 v from the new processors (af36=vss) that support v tt = 1.25 v . the output on this signal is stable when v tt is stable. refer to the appropriate platform design guide for implementation details. drdy# i/o the drdy# (data ready) signal is asserted by the data driver on each data transfer, indicating valid data on the data bus. in a multi-cycle data transfer, drdy# may be deasserted to insert idle clocks. this signal must connect the appropriate pins of all processor system bus agents. table 40. signal description (sheet 3 of 8) name type description pga370 socket occupation truth table signal value status cpupres# vid[25mv,3:0] 0 anything other than ?11111? processor core installed in the pga370 socket. cpupres# vid[25mv,3:0] 1 any value pga370 socket not occupied.
76 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process dyn_oe i the dyn_oe allows the bsel and vid signals to be driven out from the processor. when this signal is low (a condition that will occur if the processor is installed in a non-supported platform), the vid and bsel signals will be tri-stated and the platform pull-up resistors will set the vid and bsel to all 1s which is a safe setting. this signal must be connected to a 1 k ? resistor to v tt . refer to the platform design guide for implementation detail and resistor tolerance. ferr# o the ferr# (floating-point error) signal is asserted when the processor detects an unmasked floating-point error. ferr# is similar to the error# signal on the intel 387 coprocessor, and is included for compatibility with systems using ms-dos*-type floating-point error reporting. flush# i when the flush# input signal is asserted, processors write back all data in the modified state from their internal caches and invalidate all internal cache lines. at the completion of this operation, the processor issues a flush acknowledge transaction. the processor does not cache any new data while the flush# signal remains asserted. flush# is an asynchronous signal. however, to ensure recognition of this signal following an i/o write instruction, it must be valid along with the trdy# assertion of the corresponding i/o write bus transaction. on the active-to-inactive transition of reset#, each processor samples flush# to determine its power-on configuration. see the p6 family of processors hardware developer?s manual for details. this signal must be connected to a 150 ? resistor to v cc cmos1.5 . refer to the platform design guide for implementation detail and resistor tolerance. hit# hitm# i/o i/o the hit# (snoop hit) and hitm# (hit modified) signals convey transaction snoop operation results, and must connect the appropriate pins of all processor system bus agents. any such agent may assert both hit# and hitm# together to indicate that it requires a snoop stall, which can be continued by reasserting hit# and hitm# together. ierr# o the ierr# (internal error) signal is asserted by a processor as the result of an internal error. assertion of ierr# is usually accompanied by a shutdown transaction on the processor system bus. this transaction may optionally be converted to an external error signal (e.g., nmi) by system core logic. the processor will keep ierr# asserted until the assertion of reset#, binit#, or init#. ignne# i the ignne# (ignore numeric error) signal is asserted to force the processor to ignore a numeric error and continue to execute noncontrol floating-point instructions. if ignne# is deasserted, the processor generates an exception on a noncontrol floating-point instruction if a previous floating-point instruction caused an error. ignne# has no effect when the ne bit in control register 0 is set. ignne# is an asynchronous signal. however, to ensure recognition of this signal following an i/o write instruction, it must be valid along with the trdy# assertion of the corresponding i/o write bus transaction. init# i the init# (initialization) signal, when asserted, resets integer registers inside all processors without affecting their internal (l1 or l2) caches or floating-point registers. each processor then begins execution at the power-on reset vector configured during power-on configuration. the processor continues to handle snoop requests during init# assertion. init# is an asynchronous signal and must connect the appropriate pins of all processor system bus agents. if init# is sampled active on the active to inactive transition of reset#, then the processor executes its built-in self-test (bist). key i can be used to prevent legacy processors from booting in incompatible platforms. legacy processors use this pin as a reset and should be tied to ground for a 0.13 micron process processor only platform but for flexible platform implementations this pin should be a no connect. please refer to the appropriate platform design guide for implementation details. table 40. signal description (sheet 4 of 8) name type description
datasheet 77 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process lint[1:0] i the lint[1:0] (local apic interrupt) signals must connect the appropriate pins of all apic bus agents, including all processors and the core logic or i/o apic component. when the apic is disabled, the lint0 signal becomes intr, a maskable interrupt request signal, and lint1 becomes nmi, a nonmaskable interrupt. intr and nmi are backward compatible with the signals of those names on the intel pentium processor. both signals are asynchronous. both of these signals must be software configured via bios programming of the apic register space to be used either as nmi/intr or lint[1:0]. because the apic is enabled by default after reset, operation of these pins as lint[1:0] is the default configuration. lock# i/o the lock# signal indicates to the system that a transaction must occur atomically. this signal must connect the appropriate pins of all processor system bus agents. for a locked sequence of transactions, lock# is asserted from the beginning of the first transaction end of the last transaction. when the priority agent asserts bpri# to arbitrate for ownership of the processor system bus, it will wait until it observes lock# deasserted. this enables symmetric agents to retain ownership of the processor system bus throughout the bus locked operation and ensure the atomicity of lock. nchctrl i the nchctrl input signal provides agtl pull-down strength control. the processor samples this input to determine the n-channel device strength for pull- down when it is the driving agent. this signal must be connected to a 14ohm resistor to v tt . refer to the platform design guide for implementation detail and resistor tolerance. picclk i the picclk (apic clock) signal is an input clock to the processor and core logic or i/o apic which is required for operation of all processors, core logic, and i/o apic components on the apic bus. picd[1:0] i/o the picd[1:0] (apic data) signals are used for bidirectional serial message passing on the apic bus, and must connect the appropriate pins of all processors and core logic or i/o apic components on the apic bus. pll1, pll2 i the processor has an internal analog pll clock generator that requires a quiet power supply. pll1 and pll2 are inputs to this pll and must be connected to v cc core through a low pass filter that minimizes jitter. see the platform design guide for implementation details. prdy# o the prdy (probe ready) signal is a processor output used by debug tools to determine processor debug readiness. preq# i the preq# (probe request) signal is used by debug tools to request debug operation of the processors. pwrgood i the pwrgood (power good) signal is processor input. the processor requires this signal to be a clean indication that the clocks and power supplies (v cc core , etc.) are stable and within their specifications. clean implies that the signal will remain low (capable of sinking leakage current), without glitches, from the time that the power supplies are turned on until they come within specification. the signal must then transition monotonically to a high state. pwrgood can be driven inactive at any time, but clocks and power must again be stable before a subsequent rising edge of pwrgood. it must also meet the minimum pulse width specification in table 18 , and be followed by a 1 ms reset# pulse. the pwrgood signal must be supplied to the processor; it is used to protect internal circuits against voltage sequencing issues. it should be driven high throughout boundary scan operation. req[4:0]# i/o the req[4:0]# (request command) signals must connect the appropriate pins of all processor system bus agents. they are asserted by the current bus owner over two clock cycles to define the currently active transaction type. table 40. signal description (sheet 5 of 8) name type description
78 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process reset# i asserting the reset# signal resets all processors to known states and invalidates their l1 and l2 caches without writing back any of their contents. for a power-on reset, reset# must stay active for at least one millisecond after v cc core and clk have reached their proper specifications. on observing active reset#, all processor system bus agents will deassert their outputs within two clocks. a number of bus signals are sampled at the active-to-inactive transition of reset# for power-on configuration. these configuration options are described in the p6 family of processors hardware developer?s manual for details. the processor may have its outputs tristated via power-on configuration. otherwise, if init# is sampled active during the active-to-inactive transition of reset#, the processor will execute its built-in self-test (bist). whether or not bist is executed, the processor will begin program execution at the power on reset vector (default 0_ffff_fff0h). reset# must connect the appropriate pins of all processor system bus agents. reset# is the only agtl signal which does not have on-die termination. therefore, it is necessary to place a discrete 56 ? resistor to v tt . refer to the platform design guide for implementation detail and resistor tolerance. reset2# i reset2# pin is provided to differentiate the processor from the previous generation intel celeron processor. the 0.13 micron process based processor does not use the reset2# pin. refer to the platform design guide for the proper connections of this signal. rp# i/o the rp# (request parity) signal is driven by the request initiator, and provides parity protection on ads# and req[4:0]#. it must connect the appropriate pins of all processor system bus agents. a correct parity signal is high if an even number of covered signals are low and low if an odd number of covered signals are low. this definition allows parity to be high when all covered signals are high. rs[2:0]# i/o the rs[2:0]# (response status) signals are driven by the response agent (the agent responsible for completion of the current transaction), and must connect the appropriate pins of all processor system bus agents. rsp# i the rsp# (response parity) signal is driven by the response agent (the agent responsible for completion of the current transaction) during assertion of rs[2:0]#, the signals for which rsp# provides parity protection. it must connect the appropriate pins of all processor system bus agents. a correct parity signal is high if an even number of covered signals are low and low if an odd number of covered signals are low. while rs[2:0]# = 000, rsp# is also high, since this indicates it is not being driven by any agent guaranteeing correct parity. rttctrl i the rttctrl input signal provides agtl termination control. the processor samples this input to set the termination resistance value for the on-die agtl termination. this signal must be connected to a 56 ? resistor to v ss on a uni- processor platform or a 68 ? resistor to v ss on a dual-processor platform. refer to the platform design guide for implementation detail and resistor tolerance. slewctrl i the slewctrl input signal provides agtl slew rate control. the processor samples this input to determine the slew rate for agtl signals when it is the driving agent. this signal must be connected to a 110 ? resistor to v ss . refer to the platform design guide for implementation detail and resistor tolerance. slp# i the slp# (sleep) signal, when asserted in stop-grant state, causes processors to enter the sleep state. during sleep state, the processor stops providing internal clock signals to all units, leaving only the phase-locked loop (pll) still operating. processors in this state will not recognize snoops or interrupts. the processor will recognize only assertions of the slp#, stpclk#, and reset# signals while in sleep state. if slp# is deasserted, the processor exits sleep state and returns to stop-grant state, restarting its internal clock signals to the bus and apic processor core units. table 40. signal description (sheet 6 of 8) name type description
datasheet 79 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process smi# i the smi# (system management interrupt) signal is asserted asynchronously by system logic. on accepting a system management interrupt, processors save the current state and enter system management mode (smm). an smi acknowledge transaction is issued, and the processor begins program execution from the smm handler. stpclk# i the stpclk# (stop clock) signal, when asserted, causes processors to enter a low power state. the processor stops providing internal clock signals to all processor core units except the bus and apic units. the processor continues to snoop bus transactions and latch interrupts. when stpclk# is deasserted, the processor restarts its internal clock to all units, services pending interrupts, and resumes execution. the assertion of stpclk# has no effect on the bus clock; stpclk# is an asynchronous input. tck i the tck (test clock) signal provides the clock input for the processor test bus (also known as the test access port). tdi i the tdi (test data in) signal transfers serial test data into the processor. tdi provides the serial input needed for jtag specification support. tdo o the tdo (test data out) signal transfers serial test data out of the processor. tdo provides the serial output needed for jtag specification support. thermdn o thermal diode cathode. this signal is used to calculate core (junction) temperature. see section 4.1 . thermdp i thermal diode anode. this signal is used to calculate core (junction) temperature. see section 4.1 . thermtrip# o the processor protects itself from catastrophic overheating by use of an internal thermal sensor. this sensor is set well above the normal operating temperature to ensure that there are no false trips. the processor will stop all execution when the junction temperature exceeds approximately 135 c. this is signaled to the system by the thermtrip# (thermal trip) pin. once activated, the signal remains latched, and the processor stopped, until reset# goes active or core power is removed. there is no hysteresis built into the thermal sensor itself; as long as the die temperature drops below the trip level, a reset# pulse will reset the processor and execution will continue. if the temperature has not dropped below the trip level, the processor will continue to drive thermtrip# and remain stopped. in the event the processor drives the thermtrip# signal active during valid operation, both the v cc and v tt supplies to the processor must be turned off to prevent thermal runaway of the processor. valid operation refers to the operating conditions where the thermtrip# signal is guaranteed valid. the time required from thermtrip# asserted to v cc rail at 1/2 nominal is 5 seconds and thermtrip# asserted to v tt rail at 1/2 nominal is 5 seconds. once vcc and v tt supplies are turned off the thermtrip# signal will be deactivated. system logic should ensure no ?unsafe? power cycling occurs due to this deassertion. tms i the tms (test mode select) signal is a jtag specification support signal used by debug tools. trdy# i/o the trdy# (target ready) signal is asserted by the target to indicate that it is ready to receive a write or implicit writeback data transfer. trdy# must connect the appropriate pins of all processor system bus agents. trst# i the trst# (test reset) signal resets the test access port (tap) logic. trst# must be driven low during power on reset. v cmos_ref i the v cmos_ref input pin supplies non-agtl reference voltage, which is typically 2/3 of v cmos . v cmos_ref is used by the non-agtl receivers to determine if a signal is a logical 0 or a logical 1. the thevenin equivalent impedance of the v cmos_ref generation circuits must be less than 0.5 k ? /1 k ? (i.e., top resistor 500 ? , bottom resistor 1 k ? ). table 40. signal description (sheet 7 of 8) name type description
80 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process 7.2 signal summaries table 41 through table 44 list attributes of the processor output, input, and i/o signals. vid [3:0,25mv] o the vid[3:0, 25 mv] (voltage id) pins can be used to support automatic selection of power supply voltages. these pins are cmos signals that must be pulled up to 3.3 v power rail with 1 k ? resistors. the vid pins are needed to cleanly support voltage specification variations on processors. see table 3 for definitions of these pins. the power supply must supply the voltage that is requested by these pins, or disable itself. v ref i the v ref input pins supply the agtl reference voltage, which is typically 2/3 of v tt . v ref is used by the agtl receivers to determine if a signal is a logical 0 or a logical 1. vtt_pwrgd i the vtt_pwrgd signal informs the system that the vid/bsel signals are in their correct logic state. during power-up, the vid signals will be in an indeterminate state for a small period of time. the voltage regulator or the vrm should not sample and/or latch the vid signals until the vtt_pwrgd signal is asserted. the assertion of the vtt_pwrgd signal indicates the vid signals are stable and are driven to the final state by the processor. refer to figure 6 for power-up timing sequence for the vtt_pwrgd and the vid signals table 40. signal description (sheet 8 of 8) name type description table 41. output signals name active level clock signal group bsel[1:0] high asynch power/other cpupres# low asynch power/other detect high asynch power/other ferr# low asynch cmos output ierr# low asynch cmos output prdy# low bclk agtl output tdo high tck tap output thermtrip# low asynch cmos output vid[3:0, 25mv] n/a asynch power/other table 42. input signals (sheet 1 of 2) name active level clock signal group qualified a20m# low asynch cmos input always 1 bclk high ? system bus clock always bpri# low bclk agtl input always defer# low bclk agtl input always flush# low asynch cmos input always 1 ignne# low asynch cmos input always 1 init# low asynch cmos input always 1 intr high asynch cmos input apic disabled mode key n/a asynch power/other
datasheet 81 intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process note: synchronous assertion with active tdry# ensures synchronization. lint[1:0] high asynch cmos input apic enabled mode nmi high asynch cmos input apic disabled mode nchctrl n/a asynch power/other picclk high ? apic clock always preq# low asynch cmos input always pwrgood high asynch cmos input always reset# low bclk agtl input always reset2# low bclk agtl input rsp# low bclk agtl input always rttctrl n/a asynch power/other slewctrl n/a asynch power/other slp# low asynch cmos input during stop-grant state smi# low asynch cmos input stpclk# low asynch cmos input tck high ? tap input tdi high tck tap input tms high tck tap input trst# low asynch tap input vtt_pwrgd high asynch power/other table 42. input signals (sheet 2 of 2) name active level clock signal group qualified table 43. input/output signals (single driver) name active level clock signal group qualified a[35:3]# low bclk agtl i/o ads#, ads#+1 ads# low bclk agtl i/o always ap[1:0]# low bclk agtl i/o ads#, ads#+1 bp[3:2]# low bclk agtl i/o always bpm[1:0]# low bclk agtl i/o always br0# low bclk agtl i/o always d[63:0]# low bclk agtl i/o drdy# dbsy# low bclk agtl i/o always dep[7:0]# low bclk agtl i/o drdy# drdy# low bclk agtl i/o always lock# low bclk agtl i/o always req[4:0]# low bclk agtl i/o ads#, ads#+1 rp# low bclk agtl i/o ads#, ads#+1 rs[2:0]# low bclk agtl input always trdy# low bclk agtl input
82 datasheet intel ? celeron ? processor for pga370 up to 1.40 ghz on 0.13 process table 44. input/output signals (multiple driver) name active level clock signal group qualified aerr# low bclk agtl i/o ads#+3 berr# low bclk agtl i/o always binit# low bclk agtl i/o always bnr# low bclk agtl i/o always hit# low bclk agtl i/o always hitm# low bclk agtl i/o always picd[1:0] high picclk apic i/o always

▲Up To Search▲

Price & Availability of 298596-004

	To Download 298596-004 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .